Nevermore Systems Descriptions

From MITNA
Revision as of 11:08, 17 August 2009 by Mwall (Talk | contribs)

Jump to: navigation, search

This document purports to be an exhaustive list of Nevermore's various subsystems.

BOAT SYSTEMS

standing and running rigging

Standing Rigging

Rig Dimensions:

  • I: 47.00' (Height of the foretriangle, measured from the highest point of the sail attachment to the sheer line at the point abeam the mast. The point of sheer line is the intersection of the hull and deck)
  • J: 16.00' (Horizontal distance from forestay attachment point to front surface of mast)
  • P: 41.50' (Maximum hoist of mainsail, measured from lower edge of the upper mast band to the upper edge of the lower mast or upper surface of fixed boom)
  • E: 12.00' (Maximum foot length of the mainsail, measured from the after edge of the mast to the inner edge of the band on the boom)
  • Est. Forestay Len.: 49.65'

reference: sailboatdata.com

running rigging

sails

  • MAINSAIL
    • per lines drawing from web: P=41.5 ft (tack to head along mast), E=12.0 ft (tack to clew along boom)
    • Dutchman furling system (Type A)
    • traveller
    • boomvang
  • FORESAIL
    • Foretriangle: per lines drawing from web: I=47.0 ft (vertical along mast), J=15.0 ft (mast to tack point)
    • Large genoa: ~ 160%, all-white
    • Smaller genoa: ~ 130%, blue UV protection along the luff.
    • Jib: 100% ?
    • Assembly & Ops manual File:Furlex 200S Furler.pdf, also see [Docs-aboard List]
      • Operation:
        • keep a little tension on furling line as sail is deployed, to minimize line overwraps in furler drum
        • keep a little tension on jibsheets while furling, to make a tight roll of sail on the forestay
        • tension on furling line is considerable for first few turns of drum; however, NEVER apply too much tension if furler is "sticky"
    • halyard winch: dedicated, port side of mast;
      • Operation:
        • The Owner's Instructions page 6 directs that there be at least 2 turns of WIRE halyard, preferably 4, around the winch with foresails fully hoisted; and never should genoa halyard tension be taken on the rope halyard tail
        • it follows from the above that we should not consider the deep grooving of the winch drum as being anomalous
        • it also follows that the wire-to-rope splice will be wrapped on the drum (which ThomS learned is generally NOT desired on most boats)
  • SPINNAKER
    • asymetric (with Raven!)
    • pole (telescoping aluminum)

deck hardware

WINCHES

Winch # Location Lewmar
Part # 		Features Purpose
1 cockpit port 48 ST 2-speed self-tailing foresail sheet
2 cockpit stbd 48 ST 2-speed self-tailing foresail sheet
3 companionway port 16 2-speed self-tailing mainsheet
4 companionway stbd 8 1-speed self-tailing raise/lower centerboard
5 boom stbd 8 1-speed mainsail reefing/outhaul
6 mast port 30 2-speed foresail halyards
7 mast stbd 16 2-speed main halyard


[see Sys_Descript_WINCHES for more comments on maintaining the winches]

Keel-Centerboard

Nevermore's Keel/Centerboard

The keel provides weight for righting moment, and also accommodates the slot for the centerboard. The centerboard is attached to the keel by a single hinge pin at the forward end of the centerboard slot. The centerboard pennant pulls the centerboard up (as opposed to pulling the centerboard down).

(See Owner's Instructions pages 4, 5, 5A for rigging and adjusting the centerboard pennant and tag line, and pages 14, 15, 15A for replacing the pennant.)

TODO: find weights of keel and centerboard.

Operation Hints:

  • DO NOT let the pennant run free! I.e., don't let the centerboard drop!
  • The instructions show how to place the block on the pennant so that the tag line will allow full upward position of the CB, and also allow full extension of the CB when the tag line is freed.
  • Simplistic guidelines for deploying the centerboard:
    • deploy down when on the wind
    • pull up when running
    • keeping the centerboard down while backing improves steering control

Ship's Machinery

power train

engine

Identifying info from tag on engine:

  • model: Westerbeke 50
  • ser #: 18P/830A/0247B911
  • spec : 18360 2.1
  • date : November 1979 manufacture decoded from "0247B911" of serial number
    (block #0247 per Svc Bul #132, or of engine per #242; date from "B911" )


REFERENCES:

  • Our catalog of engine hardcover and web-based documents, including entries defining
    • Tech Manual (ENG_TM), and references to subsidiary tech info on this wiki and on the web
    • Westerbeke's Parts List (ENG_PL)
    • a link to the Parts List put on the web by an independent parts supplier
  • Tartan's Engine schematic dgm of 12-V DC circuitry which comes with the Engine
    • a Wiring Diagram of the circuitry on this schematic is in section Q of the Tech Manual


'Misc observations' (useful in troubleshooting):

Engine instrument panel gauges (05Sep07):
Water Temp gauge
* goes off left (cool) end with sender disconnected (good)
* sender shows 360 ohm @ 100 deg, 25 ohm @ 230 deg
Oil Pressure gauge
* goes off left (0 psi) end with sender disconnected (good)
(but note: Calder p.288 says most O.P. gauges go to high reading)
* sender shows 460 ohm @ 0 psi, 44 ohm @ 50 psi, 0 ohm @ 80 psi
See Tech Letter #72 page V.4 of Engine Tech Manual
"Gauges -vs- Senders non-Interchangeability"
engine mfgr has used 4 different gauge mfgrs for WT & OP, and each
requires sender by same mfgr; diagrams are given for configs of
connections for each manufacturer of gauge.
TODO: define here which make of gauges we have (so tested above),
and (a) mention it in the 2 sets of resistance readings above,
and (b) annotate Engine Manual
transmission
* Appears to be a "Short Profile Sailing Gear" transmission, HBW Model 10
(page S.41 of Engine Manual, by comparing it to descriptions of
about 5 different kinds of transmissions described therein,
then getting the 5, 10 or 20 size from title in |Parts List)
* Type of transmission fluid: ATF type A, or Dextron II
* fluid quantity (for Model 10): 0.6 litre
drive shaft, coupler, stuffing box
propeller
Prop, Cutlass, Zincs
Prop

The prop we got on Nevermore is fixed, 2-bladed. Size & pitch are unknown.
Note: the original standard prop was 16-inch fixed two blades [per www.practical-sailor.com Apr 2009 p.14]

TODO:

  • look for a prop model number, and/or look for an info folder aboard
  • look for a cutlass bearing model number or other info aboard
  • can we measure pitch?
  • measure shaft diameter (to replace zincs)
    • [Thom measured shaft just a little less than 1.5 inch, with dopey micrometer]
  • mark shaft inside the boat for vertical position of blades

Note that aboard is a datasheet for a VARIABLE prop. We think it is for a 2-bladed prop too. A brochure says "Martec low drag propeller." And a 1985 (I think) application for a racing handicap listed Nevermore as having a variable prop. we assume this IMS handicap application was associated with the 1985 Bermuda race.

steering & binnacle

Wheel, drive & quadrant mechanism, rudder-post
Per Owner's manual page 8, the Tartan-37 is equipped with an Edson Radial Drive pedestal steering system.
The "Information on maintenance ... included elsewhere in this manual" can't be found [ThomS Feb08].
TODO: Enter model numbers herein, and see if any ref material is on web.
NOTE: The "quadrant" is properly a "wheel" at the rudderhead [per Calder]; let's call it the "quadrant" unless talking to e.g. boatyard folk who know the difference; might have to say "rudderhead wheel" do distinguish it from the [steering] "wheel".
emergency tiller
(See Owner's manual page 8, STEERING)
  • The emergency tiller comes in two pieces.
    • One piece fits inside the rudder post, and is left there.
      • TODO: check that Nevermore's tiller piece is in the rudder post.
    • The tiller handle, a straight aluminum tube, is stored in the lazarette for immediate use.
  • The emergency tiller doesn't allow as much rudder angle as the wheel, and force on the tiller can be considerable.
  • Emergency steering may be easier, or at least less awkward, with the wheel removed.
    • The nut should be tried regularly to make sure it can quickly be undone in an emergency.
Thoughts:
  • The rudder can fail when something jams in the steering quadrant.
    • In which case, the tiller may not steer the boat.
      • One might mentally rehearse using the emergency tiller to work the jam free.
    • While responding quickly and resolutely, no crew should take chances at getting caught in the cabling or chains while unjamming the cables/quadrant.
    • One might mentally rehearse the sound signals for Vessel Not Under Command before needing the signal.
  • One might rehearse on the water what the emergency tiller feels like when used with the rudder NOT jammed, to have an idea of whether it IS jammed when the steering breaks, since it usually requires a lot of force even when the steering is NOT jammed.
Autopilot

According to the Autopilot manual page 8, a basic autopilot system consists of:

  • Control Unit (AP11)
    • located on port cockpit combing in driver's seat
  • Junction Unit (J3000X)
    • located on fuel tank bulkhead behind nav station seat
  • Drive Unit (no model # page 8, RPU80/RPU180 per diagram page 9)
    • located to port of steering quadrant in stern lazaret, attaches to underside of quadrant
  • Fluxgate Compass (RFC35) (Serial No.: 13134E02)
    • located behind port settee, just forward of nav station.
    • front of compass is facing stern so it needs offset correction of 180 degrees during system setup.
  • Rudder actuator (is this "Reversible pump RPU80 or 160" listed in the manual?
    • location: port quarter, attached to rudder quadrant
  • Rudder Feedback Unit (RF300)
    • location: aft of steering quadrant, a little stbd of centerline; attaches to top of quadrant
  • Course Detector Interface (CD135) (didn't see one; is this optional?)
  • Rate Compass (RFC35R) (didn't see one; is this optional?)
  • power feed from ship's 12V subsystem
    • switch #2 observed on vertical set of Nav station switches (we did not trace this circuit to the system (Fall '07))

STATUS:

  • Fall '07:
    • we never tried to operate it
    • saw NO current load when AUTO PILOT circuit breaker was turned ON;
    • expected to see a stand-by current, but it MAY have been too small to observe since AP11 Control Unit max current < 1/2 amp when ON and illumination fully on
  • Spring '08:
    • turning system ON at steering station Control Unit didn't seem to activate anything
    • removed actuator from rudderhead wheel because unit is frozen and steering was jammed

bilge pumps

Electric Bilge Pump

Jabsco Water Puppy (Model 18660-0121).

Specs:

Body Bronze
Impeller Neoprene p/n 6303-0001, -0003 nitrite for oil-resistence
Voltage 12 Vdc
Amp Draw 8 amp
Fuse Size 15 amp
Port Type 1/2" Internal Pipe Threads
Dimensions 3 x 4-3/4 x 6-3/8 inches (7.6 x 12.0 x 16.2 cms)
Weight 4-1/2 lb (2 kg)

More information can be found in the Jabsco Water Puppy Technical Data Sheet

This pump is mounted on the port side of the stern lazarette. A white, corregated plastic ("Bilge-flex"), 3/4" I.D. hose leads from the bilge to the pump. A white, corregated plastic, 5/8" I.D. hose leads from the pump to a through-hull port on the starboard side near the stern. Note that this is the same port used by the manual bilge pump.

BilgepumpCircuit.gif

The bilge pump is wired directly from battery #1 to the 3-way switch on the nav station breaker panel. The up position manually turns on the pump. The down position puts the pump in automatic mode, in which a "float switch" will turn on the pump when water level in the bilge rises. A 15-amp fuse is inline with the positive lead from battery #1. The yellow rubber fuse holder for this fuse is strapped to the wiring harness that runs directly above battery #1.

Also see Bilge pump 3-way toggle switch table for an outline description of the above paragraph.

The float switch (which doesn't actualy float) for the bilge pump is located behind the aft-most panel above the port bench in the cabin (just forward of the nav station). An orange hockey-puck-sized rubber cover surrounds a microswitch which is affixed to a rubber diaphram. A black plastic air tube runs from the diaphram to a plastic air bell in the bilge. Rising water in the bilge will increase air pressure in the tube and activate the switch. 

As of 9/3/2007, the switch is not sensitive enough to be activated by 6 inches of water.  
Deeper water might activate the pump, but the required depth is unknown.  
A newer model float switch (Jabsco Hydro Air Bilge Switch) will be ordered.
Old switch probably Licon Switch 11-330071 10-amp (per Thom scruffy note).
Manual Bilge Pump

This pump is mounted on stern lazaret to starboard of steering position. Its handle is tied to boat in stern lazaret. A second handle is aboard. Gray corrugated plastic hose, approx 1", leads from bilge to pump.

TODO: define hose to thru-hull, and position of thru-hull.

TODO: define model number, capacity, etc., of pump.

head

Nevermore Blackwater Plumbing Schematic

Nevermore is equipped with a standard marine toilet and a plastic holding tank. It is classified as a "Type III Marine Sanitation Device", which means that the waste is not treated, it is simply stored inside the holding tank until it can be pumped out. Note that there is no way to pump out the holding tank from the boat; the waste must be sucked out of the holding tank through the "waste" deck fitting.

The yellow handled seacock under the sink in the head allows seawater to be pumped into the toilet bowl. This seacock also serves as a scupper for the sink.

If the flush valve next to the hand pump is in the "flush" position (vertical), then seawater will be pumped into the bowl when the the hand pump is operated. If the flush valve is in the "pump dry" position (horizontal and to port), then no seawater will be added to the bowl during pumping.

The hand pump simulateously pumps seawater into the bowl (if the flush valve is open) and waste out of the bowl. The waste is pumped through about 15 feet of 2" O.D. hose, which includes an anti-siphon loop. After the loop, the waste goes into a plastic Y-valve with a blue handle that is under the sink basin. If you can read the words "to tank" on the blue handle, then the waste is being pumped into the holding tank under the port side V-berth. If you can read the word "overboard" on the blue handle, then waste is being routed to the large bronze seacock.

During normal operation of the vessel, the Y-valve should be in the "To Tank" position and the large bronze seacock should be closed.

Three hoses go from the holding tank up to the port side deck. A 2" diameter hose goes to the pumpout port on the deck (labeled "Waste"). A 1" diameter hose goes to a water inlet port next to the pumpout port. This inlet has garden hose threads and can be used to facilitate flushing out the holding tank. Another 1" diameter hose goes from the top of the holding tank to an air vent on the upper topsides, just below the pumpout port.

Ice Box

The ice box is cooled by ice or by DC refrigerating system. There are two levels in the cooler, separated by a wood lattice. Water from the ice box drains to the bilge.

The refrigeration system has two parts, a compressor (mounted in the starboard lazarette) and an evaporator (located in the ice box). The thermostat is located in the back (outboard) part of the ice box. The compressor is Adler/Barbour BD2,5 02N3111

The ice box is mentioned in the Owners Manual page 11.

STATUS: as of 12apr09, do not use the compressor to cool the refrigerator. it draws some current but apparently does not do any cooling.

TODO: record volume of ice box

Stove

See T37 Owner's Instructions pages 16-17 for operation of the stove.

SAFETY COMMENTS:

Based on experiences on Aleida with the same kind of stove, a few items of these instructions should be highlighted.

  • The statement that "the gas is burned in much the same manner as in a home has stove" is literally true, but somewhat misleading because it might imply that one turns on the gas, lights the stove, and is ready to cook. However, the steps 7, 8, 9, and part of 10 -- which comprise turning on the gas and lighting the stove, imply a more complicated situation, and with good reason.
  • Especially step 7 -- wherein we get some alcohol into the lower part of the burner -- is important to get right. We can suggest looking in the burner with a flashlight as the valve is turned on to "watch the alcohol flowing into the little pan," to make SURE not to get too much fuel in the little cup. Maybe the "one turn" on is an excessive amount to turn the valve on, unless the stove hasn't been used for awhile. [At least one Aleida skipper found it IMPOSSIBLE to describe what's needed without a demonstration...]
  • Part of the instructions in step 8 include "if the flames are licking at the overhead, ... extinguish with water." Think about it: if you're gonna boil some water anyway, why not draw it BEFORE your first times at lighting the stove.
  • We note that step 11's order of turn-off (master shut-off valve first, then burner valve) may be different from instructions in the paperwork that came with the stove, and was not used on Aleida as far as I [ThomS] knows. However, it does give a more safe condition for the stove when it isn't being used, purging pressure from the fuel line.

Fresh Water System

Page 10 of the T37 Owner's manual describes operation and maintenance of the fresh water system; however, the system has been changed, especially concerning filling the tanks, as mentioned later below.

The fresh water system is supplied by 2 tanks, a 30-gallon tank on the port side, and a 60-gallon tank on the starboard side. Each tank has 2 inspection ports which are easily accessed through the lower berth/bench on either side of the main cabin.

Valves under the cabin floor connect the two tanks. Either tank can supply water to the ship's fresh-water system, or both tanks can be linked together.

There are two fill fittings on the starboard deck; the forward fill fitting fills the port tank, and the aft fitting fills the starboard tank.

The original configuration had only ONE fill fitting. Nevermore's copy of the Owner's manual has been marked up to indicate how to fill both tanks (the original configuration required filling the port tank through the starboard tank.)

Note the admonition (also on page 10, in the "HOT WATER" section) that the fresh-water pump should be ON while heating water using 110-volt shore power. The water is usually warmed by the engine's fresh-water cooling water; this does not require the pump to remain ON; there's no control to turn this heating on or off.

A rough sketch of the water system is being used (2007-08) to replace all the freshwater hoses; it indicates all associated devices and parts, and indicates their planned interconnection.

Freshwater System Schematic

(this is a rough diagram - just testing my ability to upload images to the wiki)


Fresh Water Pump
Nevermore Water Pressure Pump

Jabsco Par-Max 3.0 (Model 31395-3000).

Specs:

Voltage 12 Vdc
Amp Draw 5.2 amp @ 10 PSI
Fuse Size 10 amp
Flow 3.0 GPM
Ports "Snap-Fit" ports with 1/2" hose adapters
Dimensions 9 x 4.2 x 4.75 inches
Weight 4-1/2 lb (2 kg)

The water pressure pump is located just forward of the starboard tank, under the lower berth. Diaphram design allows pump to run dry without damage. Internal pressure sensor stops the pump when working pressure is acheived.

Fresh Water Strainer
Nevermore Fresh Water Strainer and Accumulation Tank

Jabsco Pumpgard (Model 36400-0000)

Water from one or both tanks is filtered by a steel screen strainer which is inline just before the water pump.

The strainer can be cleaned by unscrewing the plastic cover from the top, removing the cylindrical screen, and rinsing it out with fresh water.

Water Heater

Nevermore's water heater is a Raritan 1700, 12-gallon, 120V heater, Model #171211. This unit was purchased Spring 2008.

Specifications:

  • Electrical Recovery Rate = 13 gallons (49.2 liters) per hour
  • Maximum Operating Pressure:
    • Tank: rated at 150 psi (1034kPa)
    • With Temperature and Pressure Valve Installed: 50 psi (345kPa)
  • Amps: 10 (120V AC)
  • Required Circuit Breaker: 15 amps
  • Thermostat: Adjustable; Factory Set to 120°F (49°C)
  • Anode: Magnesium

Raritan Water Heater Manual

Maintenance issues:

  • Magnesium anode should be checked once per year


Ship's Electrical Subsystems

The 12-volt DC wiring circuits and the 110-volt AC circuits are functionally and electrically isolated from one another, except for the 12-volt battery charger which is powered by 110-volt AC shore power. DC-to-AC ground isolation must be performed within the charger.

The Tartan 37 wiring diagram provided in the Owner's Instructions can be used as a general guide to Nevermore wiring. However, this Oct 1976 drawing is different from the 1980 as-built configuration as we deduce it, as discussed in comments to the wiring diagram.

The as-received (2007) configuration of wiring will be discussed in sections for 12-V DC and the subsection battery charger, and in section 120-V AC below.


12-Volt DC

Switch Panel at Nav Station
Meters, Bilge Pump Switch and Main Switch Panel

The switch panel above the nav table is organized into groups of controls including (from left to right):

  1. Meters for battery voltage and current
  2. Electric Bilge Pump Switch (switch #01)
  3. Main Switch Sub-Panel - two horizontal rows of 6 switches or switch/breaker combination
    1. top row has 6 switch/breaker devices (switches #11 - 16)
    2. bottom row (probably) has 6 switch-only devices (switches #21 - 26)
  4. Secondary Vertical Switch Sub-Panel - 7 switching devices a mix of switch-only and switch/breakers (switches #31 - 37)
  5. Nav Instruments Sub-Panel

Meters (volts and amps)

Meter ranges: voltmeter 0 - 25 VDC; ammeter 0 - 50 A

Voltmeter quirk: it appears to read high by approx 1.4 or 1.5 volts. The zero-point for the meter has been adjusted to read battery voltages correctly therefore the zero-point will be off-scale.

  • Note: an expanded-range voltmeter might be better, e.g. 9 - 15 VDC.

Ammeter reads only the current being used by some of the ship's systems, but not any usage by the engine; it especially does not indicate battery charging; the ammeter on the engine control panel does that.

In addition, the ammeter terminal with 12-V feed from the batteries (red "thick" wire (approx #10-gauge) also has a "thick" white wire going back out of the panel via the wiring bundle; we suspect there's a ship's system which is powered by this wire which does NOT have its current reported by the ammeter.

TODO: trace the white "thick" wire from the ammeter and find the unknown ship's system.


Electric Bilge Pump Switch

  • OFF, AUTOMATIC, or MANUAL operation of the single bilge pump.
  • Voltage is ALWAYS on to this switch, even when main rotary switches are OFF.
  • It is always connected to power from Battery #1, through an inline fuse located in the wiring harness above the battery. Removing the fuse removes voltage from the main panel's bilge-pump circuits.
  • See Electric Bilge Pump

A note on terminology: The terms "bilge" and "sump" are synonymous on Nevermore; Tartan's original "sump" was a separate catch-basin for ice box and shower water, while "bilge" was used normally. As far as we know (Sep07), the "sump" isn't used any more, and we use the 3-way switch to provide

  • TODO: mark up T37 Owner Manual page 11 to NOT talk about the "sump".
  • TODO: check whether the refigerator (ice box) still drains water into any kind of sump.


Main Switch Sub-Panel (horizontal switches)

  • Twelve combination switches/circuit-breakers arranged in two horizontal rows (switches #11-16 and 21-26).
  • Battery voltage to this sub-panel's switches is OFF unless battery power is ON on one (or more) main rotary battery switch.
  • No voltage is applied to the remainder of the 11 switches unless the upper-left-most switch of this sub-panel (named "MAIN") is on.


Vertical Switch Panel

Vertical Switch Sub-Panel at Nav Station (switches #31-37)

Note that the horizontal sub-panel's "main" switch does NOT control power to this sub-panel; it is not separately fused.


Nav Instruments Sub-Panel

Nav Instruments Sub-Panel

This control subpanel is completely disconnected.

Batteries

Batteries #1 and #2

  • Batteries #1 & #2 controlled by top main rotary switch.
  • They are "mixed use" (starting and deep discharge) batteries of the same type
  • They are located below nav station seat: #2 is fwd, #1 aft
  • Model: Powermaster DC-27P, flooded, 750 MCA, 200 min reserve

Battery #3

  • Battery #3 is controlled by bottom main rotary switch.
  • It is a "heavy duty marine starting" battery
  • Located under the stairs, just forward of the engine.
  • Model: Powermaster (unknown model), flooded, (unknown values)

Rotary Battery Switches

  • The two rotary battery switches are Guest 2300A, 360-amp, 600-amp momentary.
  • Both have AFD (alternator field disconnect) but they aren't wired, hence it is very important that at least ONE battery be selected ON at all times that the engine is running.

Emphasizing importance of above: we've found NO alternator protector (West Marine catalog index term) to prevent over-voltage from blowing the alternator's diodes when all batteries are turned "OFF" while running the engine; nor are the AFD (alternator field disconnect) contacts on the main switches wired (nor can they BE wired, with the present wiring of the bottom switch Batt #2 contact.)

  • TODO: put some of the AFD unwirability discussion in a "quirk" section,

and make a simpler statement in THIS paragraph...


Navigation Lights
Tricolor, Anchor, Strobe

Tri-Color/Anchor/Strobe

  • Model: Aquasignal Series 40: tricolor / anchor / strobe, quicfits (Model # 40806)
  • "Quicfits" connector means that the unit can be easily unclipped from the top of the mast by sqeezing the black tabs at the bottom of the unit and pulling the whole assembly up.
  • Bulbs:
    • tricolor: 12V, 25W, 15D bayonet base (Aquasignal Part# 90002)
    • anchor: 12V, 10W, 15D bayonet base (Aquasignal Part# 90005)
    • strobe: 12/24V, 8W, Xenon Strobe (Aquasignal Part# unknown - maybe 90009)
  • Visibility (from Aquasignal website):
    • tricolor: 2nm
    • anchor: 2nm
    • strobe: 3nm
  • Aquasignal Website


Dissassembled Steaming / Foredeck Light Assembly

Steaming/Foredeck Light

Make and model is unknown. Similar models use 10W bulbs for steaming light and 20W flood bulbs for foredeck illuminaton.

  • TODO: determine make and model
  • TODO: determine bulb types


Sidelights

The sidelight fittings have red and green lenses. They use a double-contact bayonet-base bulb. Base-diameter is 19/32", and bulb is 1-3/8" long. Nevermore's sidelights are required to have 1 Candlepower (cp) of luminous intensity.

Bulbs that came with Nevermore are 12v, 3W, 4.5cp, such as Seadog Part# 441032-1.

As of August 2009, two spare bulbs were aboard, Ancor Part# 520090: 12v, 7.5W, 6cp.

Sternlight

  • TODO: determine bulb type
120-V AC Battery Charger

Xantrex Truecharge 10TB Multistage Battery Charger.

This charger uses microprocessor-controlled three-stage charging:

  • Bulk: Replaces 70-80% of the battery’s state of charge at the fastest possible rate.
  • Absorption: Replenishes the remaining 20-30% of charge, bringing the battery to a full charge at a slow, safe rate.
  • Float: Voltage is reduced and held constant in order to prevent damage and keep batteries at a full charge.

Specs:

Output current 10 A @ 14.5 V nominal
Output voltage (charge) 14.2 - 14.4 VDC
Output voltage (float) 13.5 - 13.8 VDC
Input voltage 90-135 VAC, 50/60 Hz)
Number of battery banks 2
Configurable battery settings Sealed (Gel & AGM) / Flooded
Recommended battery size 25 Ah to 100 Ah
Dimensions (H x W x L) 2.75 x 6.7 x 15.1 inches
Weight 3 lb
AC Connector 3-prong 15A household plug
DC Connectors Two 2-pin molex connectors

Documentation on this charger:

Note: This charger is not yet installed. See the Upgrade 120v Electrical System task for more details.

The previous battery charger was Battery Charger Raritan R3012-3. It was removed from the boat in July, 2008.

120-volt AC

120-volt AC power is supplied to the ship via a standard male twist-lock shore power connector (NEMA type L5-30), mounted on the exterior of the port-side cockpit coaming by the stern.

  • Note: The shore power is the aft-most of 2 connectors. The other connector was for "phone" and is completely disconnected.

Two switches/breakers are mounted on the aft side of the "Emergency" supplies cabinet next to the nav station. The Tartan documentation lists these as 20-amp breakers, although no amperage is designated on the actual breakers.

The left breaker is labeled "110 V AC" and supplies power to standard household AC receptacles (NEMA type 5-15). One pair of receptacles is above the galley sink, and another pair of receptacles on the aft side of the sink cabinet in the head.

The right breaker is labeled "WATER SYSTEM" and supplies power to the water heater. The power cable to the water heater is not connected (as of Nov 21 2008). The "110 V AC" breaker does not need to be switched on for the water heater to work. However, the Owner's Instructions pp. 10-11 demands that -- when the water heater 110V breaker is ON -- the freshwater pump must also be left ON.

All 120v cables terminate in a round plastic junction box located on the port side, just forward of the nav station, in a cabinet where life jackets are stowed.

  • Note: The ground connectors of all receptacles and cables are all connected together but none are connected to the DC grounding/bonding system of the boat.

The Tartan 37 wiring diagram provided in the Owner's Instructions Section V presents the 120V-AC circuitry on Nevermore as MIT received her, except that the battery charger isn't shown. (Remember that the 12V-DC circuitry on this schematic can only be a general guide to some circuit configurations.) Note that this diagram explicitly states that "shore power is totally independent from ship's ground;" i.e., it is unlikely any galvanic isolator or isolation transformer was removed from the boat like one might think.

The diagram below shows the 120V-AC configuration after the battery charger that came with Nevermore was removed.


Nevermore 110ac.png

Miscellaneous notes:

  • Two shore power cords are aboard, both with 30A (120-volt) locking connectors. Each is probably 25 foot length or more.
  • Three or four short converter cables convert from male "marine" locking connector (on dock) to 3-pin "household" female; "household" male to "marine" female to the boat; don't remember the 2 others, probably e.g. 120-volt 50-amp locking male to 20/30-amp and/or 1 leg of 240-volt locking male to 20/30-amp locking female.

TODO:

  • define and implement AC -vs- DC grounding circuit and circuit breakers to
    • provide isolation of AC & DC grounds to preclude galvanic action on ships parts
    • provide safety grounding and circuit-breakers to prevent crew electrocution or fires for a mis-wired AC feed
  • check the config of the 2 short converter cords Thom can't remember what are (see above).
  • measure length of the two long cords.
  • define steps for polarity checking of the shore power source: for example, something like:
    • first choose shore power adaptor to get to 30-amp shore-power receptacle (if required);
    • use shore-power -to- flat-pin ("household") connector to then use ground-test lights unit to check the dock's configuration; (use boat end of shore-power cable if dock power is 30-amp connector)
    • connect shore-power cable to boat;
    • (can also) use ground-test lights unit in ship's flat-pin receptacles.


Anti-Electrolysis

See also discusssion of Electrolysis (AKA "galvanic corrosion" and "stray-current corrosion".)

Zinc Guppy

Cable should be clipped to backstay and threaded through ship's wheel.
Note that stern pulpit and lifelines are not grounded (2007).


2 Engine zincs
Zincs in Engine

There are two pencil-zincs protecting the engine; one is in the heat exchanger, and one is in the oil cooler.

See Engine zincs replace 2007 for a report and discussion of replacing the two engine pencil-zincs.

See pp.220-221 Westerbeke Parts List, item 33, #11885

  • pencil-zinc in heat exchanger item 23
  • pencil-zinc in lube oil cooler item 32

Engine manual mentions something like "zinc in heat exchanger" (p.20) but doesn't mention one in oil cooler.


2 prop-shaft zincs
Zinc on Prop-Shaft

P1090819-zincs-2007-144p6q shows the prop-shaft zincs Fall 2007, printed large enough to show their inhabitants and erosion of the zinc a bit. Two new zincs were installed on prop shaft Spring 2008.

Anode in Water Heater

There is a magnesium anode in the water heater. [See water heater section.]
Note that this anode is in the engine fresh cooling water circuit; a zinc anode is NOT applicable. Anodes can be ordered from Raritan; the manual says anode part number is 1790010 for our 12-gallon tank.
TODO: Locate the anode on the unit and document it herein.

lightning-dissipation

Nevermore has NO specific lightning-dissipation .


Electronics

Fathometer

Model: Datamarine SL200DL

Serial No.: 012726

Depth Transducer:

  • Model: Airmar B17 "Retractable Low Profile"
  • Frequency: 200kHz
  • Part No. (on cable tag): 31-241-3-01
  • Purchased new: May 2008

Powered on by "NAV INST" circuit breaker on Nav Station Switch Panel 1. "MAIN" breaker switch must be on.

Tested on Aug 11, 2008. Depth sounder reads 25 feet in 28 feet of water.

Knotmeter

Model: Datamarine DCS100

This instrument is missing. It was last seen Fall 2007.

The speed transducer is in the posession of Ted Young.

The "dummy plug" core is in place in the boat.


Windmeter

Model: Datamarine LX360

Serial No.: 012128


GPS - Fixed Mount

Model: Garmin GPSMAP 276C

Software Revision: 5.20 (current as of Jun 9, 2008)

Specifications:

Unit dimensions: WxHxD 5.7" x 3.2" x 1.9" (14.5 x 8.1 x 4.8 cm)
Display size: WxH 3.0" x 2.2" (7.6 x 5.6 cm)
Display resolution 480 x 320 pixels
Display type 256-color TFT
Weight 13.6 oz (385 g)
Battery rechargeable internal lithium-ion
Battery life up to 15 hours
Waterproof yes (IPX7)
Antenna detachable 50-ohm BNC
NMEA input/output NMEA 0183
Basemap yes
Built-in memory none (cannot load maps to internal memory)
Accepts data cards Garmin data cards
Waypoints 3000
Routes 50
Track log 10,000 points

Features:

  • Garmin sonar compatible: yes
  • Supports DSC (displays position data from DSC capable VHF radio): yes
  • Audible alarms: yes
  • Tide tables: yes
  • Hunt/fish calendar: yes
  • Sun and moon information: yes
  • Automatic routing (turn by turn routing on roads): yes
  • Headphone jack/audio line-out: yes

Garmin Chart Cards:

  • Bluechart: Cape Cod: Model US003R (Jun 2007)
Gloucester through New London, including Narragansett Bay, Block Island, Martha's Vineyard, Nantucket Island, the entire Cape, and includes general coverage Georges Bank
  • Bluechart: South Maine: Model US002R (< 2006)
Penobscot Bay through Gloucester, including Casco Bay and Cape Ann

Documentation:


GPS - Handheld

Manufacturer: Magellan

Location: drawer under nav station


RADAR

  • Display: Ratheon R20XX display unit (mounted to the left of the nav station)
  • Antenna: Raytheon R20XX raydome antenna (mounted on the mast)

Status (May 23, 2008) System has been tested "on the bench" and appears to function correctly. See full status report


RADAR detector

C.A.R.D. (Collision Avoidance Radar Detector)

  • Manufacturer: Survival Safety Eng., Inc.
  • Model No.: 060
  • Serial No.: 9140470604

Detects radar signals from other boats and sounds alarm and indicates octant of bearing to the ship.

Not installed as of June 9, 2008


VHF Radio - Fixed Mount

Tranceiver:

Model unknown

Coax Cable:

  • 16(19X29) stranded tinned-Cu center conductor
  • Foam dielectric
  • Type IIA white marine jacket
  • Nominal Impedance 50 Ohm
  • Velocity of propagation 78%
  • Outer diameter .242"
  • 98% tinned Cu braid.
  • installed new cable in mast: May 2008

VHF Antenna:

  • Manufacturer: Digital Antenna
  • Model: 200 Series: 222-VW
  • 3-foot stainless steel antenna mast
  • Quick antenna mast disconnect
  • Connector: UHF female (SO239)
  • Impedance: 50 ohms
  • Max Power: 100 watts
  • 3dB gain
  • VSWR: < 1.2:1 @ 156.8 MHz
  • Ordered new: May 2008


VHF Radio - Hand-held

Model: Icom VHF Marine Tranceiver IC-M34

  • Serial No.: 0115406

Features:

  • Submersible (1m depth for 30 min.)
  • Dual/Tri-watch functions
  • Weather channel reception
  • Auto Scan function

Specifications:

Transmit Frequencies 156.025 - 157.425 MHz
Receive Frequencies 156.050 - 163.275 MHz
Usable channels INT, USA, CAN, WX channels
Type of emission 16K0G3E (FM)
Transmit Current (at 5W output) 1.5A
Receive Current (at AF max.) 200mA
Antenna Impedance 50 ohms (SMA)
Dimensions (WxHxD) 2-7/16" x 3-13/16" x 1-17/32" (62 x 97 x 39 mm)
Weight 10.8oz (305g)
RF output power (Hi/Low) 5W, 1W (2W w/ alkaline batteries)
Audio output power 0.35 W
  • Charger: Icom Desktop Charger BC-173
Retrieved from "https://sailing.mit.edu/wiki/index.php?title=Nevermore_Systems_Descriptions&oldid=3402"