Difference between revisions of "Mashnee task list"
From MITNA
(→Miscellaneous) |
|||
| Line 15: | Line 15: | ||
* Remove knives -- Gavin to resharpen | * Remove knives -- Gavin to resharpen | ||
* Remove all cutlery, plates, pots, etc. | * Remove all cutlery, plates, pots, etc. | ||
| + | |||
| + | = Dion's Work = | ||
| + | =Centerboard= | ||
| + | *Plan is to pull the board right away when hauled. | ||
| + | *Grind off head until it swings easily through wood on top of the lead keel while swelled up. Put the boat back into water to make certain it swings freely with the box wet and swollen up. Remove board again and glass up properly and install downhaul line up through the tube to the cabin top as well. New bright red paint. | ||
| + | *Get 1" half oval from Hamilton for Gasket Plates. Two 8' pieces... Cut to fit. Drill and counter sink for 1/4" screws on drill press. Install gasket beneath. Mark edges then, remove and re-cut gasket with hot knife. Then finally install... | ||
| + | |||
| + | == Rigging, Hull, Motor == | ||
| + | * Replace spreader lights - convert to LEDs with lower profile, mount them better. Dions | ||
| + | * We need a new (3rd) cowl vent, one went missing at the start of the season. Dions | ||
| + | * Inspect all standing rigging, grease Furlex bearings top and bottom | ||
| + | * All the hatch hinges need to be strengthened, replaced and/or repaired. We had water intrusion and loss of almost all of them this year (I think it was time catching up to them?) Dions | ||
| + | * The forward hatch teeth (the part attached to the hull that the latch goes in) needs to be re-attached. Thru bolted in bronze pls Dions | ||
| + | * The whole inside of the hull needs to be gone over, especially in the cockpit lockers. There was significant mold/mildew buildup. Dions in Spring? | ||
| + | * Scrub bilges around engine with Dawn or Joy to remove fuel leak residue | ||
| + | * Scrub overhead above refrigerator to remove mildew | ||
| + | * Create a way to hold the lid under the forepeak berth open when rummaging for supplies. Dions | ||
| + | * Topsides touch-up again? Re-paint next year? Check plank ends at transom, please. | ||
| + | * Bottom paint, What brands are best? Sea Hawk? | ||
| + | * Varnish- Cabin top, toe rails, coamings, tiller, companionways, hatches, spars- Interior surfaces? | ||
| + | * Motor- Change oil and filter. Leave spare filter on board | ||
| + | * Replace low-pressure engine oil line near on-engine fuel filter that has a nick and slow oil leak. It is getting worse. (+ reattach to prevent chafe; check other lines for potential chafe). | ||
| + | * Check forward starboard engine mount- seems off | ||
| + | * Polish fuel tank- Boat should arrive with less than 1/3 tank | ||
| + | * Purge water systems and flush/ bleach | ||
| + | * Fresh o rings and gaskets on fuel fill, fresh water fill and holding tank | ||
| + | * Flush and purge poop tank? Boat will arrive fully pumped out | ||
| + | * Replace or repair two bent stanchions | ||
| + | |||
| + | = North Work = | ||
| + | * We need a new canvas boot for the mast-deck connection. North. | ||
| + | * Two little covers for furler line port. North | ||
| + | * 140 work: Luff tape torn, need to buy a pre-feeder, Shorter aft batten along 140 foot | ||
| + | * Big red spin- tear near clew repaired | ||
| + | * Mainsail cover inspected and repaired as needed | ||
| + | |||
| + | = Other outsource = | ||
| + | *Code Zero - must work with current hardware. Sleeve - to fit cable. | ||
| + | *New #3 jib? | ||
| + | * Second spinnaker halyard done properly - consistent in diameter | ||
| + | * Replace dyneema topping lift? | ||
| + | |||
| + | = MIT Work = | ||
== Random Work == | == Random Work == | ||
* Buntlines for main sail reefing (these are the lines that pass through the grommets in the sail) | * Buntlines for main sail reefing (these are the lines that pass through the grommets in the sail) | ||
| − | |||
* Bungees on head hatch - Gavin | * Bungees on head hatch - Gavin | ||
| − | |||
* Mounting for compass? New compass? | * Mounting for compass? New compass? | ||
== Sails== | == Sails== | ||
| − | + | * Working jib - bolt rope on the luff frayed near the head - maybe not needed if replacing? | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | * Working jib - bolt rope on the luff frayed near the head | + | |
==Rigging== | ==Rigging== | ||
| − | |||
| − | |||
* Replace jib sheet - same diameter, length + 1' - maybe just fix? | * Replace jib sheet - same diameter, length + 1' - maybe just fix? | ||
| + | * Whipped jib sheet ends | ||
* Replace or end for end the main sheet | * Replace or end for end the main sheet | ||
* Cunningham purchase system to easily be soft shackled on when needed - carabiner? | * Cunningham purchase system to easily be soft shackled on when needed - carabiner? | ||
| − | |||
* Longer jib furling line to let us lead it aft? Soft shackle fairlead? | * Longer jib furling line to let us lead it aft? Soft shackle fairlead? | ||
* Winches broken down and greased - Gavin | * Winches broken down and greased - Gavin | ||
* Jib prefeeder - us | * Jib prefeeder - us | ||
| − | |||
* New cable for spinnakers | * New cable for spinnakers | ||
* Tack line hardware for attaching spin roller furler to a jamming bight - delay for now? | * Tack line hardware for attaching spin roller furler to a jamming bight - delay for now? | ||
| Line 49: | Line 82: | ||
* Replace all cotter pins | * Replace all cotter pins | ||
* Double smaller block for jib halyard. - Us | * Double smaller block for jib halyard. - Us | ||
| − | |||
| − | == | + | == Shopping List == |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
* purchase some of those blue grippy gloves or similar for the boat to have for people to use | * purchase some of those blue grippy gloves or similar for the boat to have for people to use | ||
| − | * | + | * Purchase more sail ties that are extra-long -- webbing -- Fran |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
* Procure more hand sanitizer for onboard use | * Procure more hand sanitizer for onboard use | ||
* Procure more hangers for the foulies (maybe wood? or stronger plastic) | * Procure more hangers for the foulies (maybe wood? or stronger plastic) | ||
| Line 80: | Line 93: | ||
* Procure some chamois for proper clean-up | * Procure some chamois for proper clean-up | ||
* Procure a pool noodle (or something else) for storing the battens | * Procure a pool noodle (or something else) for storing the battens | ||
| + | * Purchase new self-sealing washer for fuel stop solenoid and replace: Volvo Part 21424327 | ||
| + | * Purchase Extra racor filters and a | ||
| + | |||
| + | ==Miscellaneous== | ||
| + | * Handle to replace capstan? Get Fran a drawing | ||
| + | * Housing for the radar reflector—a bag or permanent hook or both | ||
| + | * Figure out anti-fouling for the dinghy motor (doesn't tilt far enough up to keep prop out of water). | ||
| + | * Anti-foul the dinghy bottom | ||
| + | * All the dinghy glue | ||
| + | * Replace eye for lee cloth on port berth | ||
| + | * Repair screen on the starboard porthole | ||
| + | * More permanent repair to companionway screen (+ better place to store) | ||
* Replace flag on end of windex triangle | * Replace flag on end of windex triangle | ||
* Winch handle release issue -- can we fix this? | * Winch handle release issue -- can we fix this? | ||
* Shave bilge panels for easier access? | * Shave bilge panels for easier access? | ||
* Grease companionway tracks | * Grease companionway tracks | ||
| + | * Spruce up soundproofing around the engine | ||
| − | |||
| − | |||
| − | |||
==Radar and electronics== | ==Radar and electronics== | ||
| − | * | + | * Base for radar mount? |
* Full electronics meeting to follow. Radar/new MFD, etc? Both B&G and Raymarine reps just recommended getting a new raymarine radar. To replace the MFD we’d also need to replace a lot of the sensors around the boat. | * Full electronics meeting to follow. Radar/new MFD, etc? Both B&G and Raymarine reps just recommended getting a new raymarine radar. To replace the MFD we’d also need to replace a lot of the sensors around the boat. | ||
* New Raymarine radar so that we can it to display on the chart plotter? | * New Raymarine radar so that we can it to display on the chart plotter? | ||
* Get rid of gremlins in the wireless displays (voltage boost?) | * Get rid of gremlins in the wireless displays (voltage boost?) | ||
* Get touchscreen physical buttons properly working | * Get touchscreen physical buttons properly working | ||
| − | * Get a new MMSI and reprogram everything so we don't conflict with "FUSION" on the west coast? | + | * Get a new MMSI and reprogram everything so we don't conflict with "FUSION" on the west coast? -- AIS MOB, VHF, etc. |
| − | + | ||
* Engine panel electrical gremlins - clean and reseat all contacts… | * Engine panel electrical gremlins - clean and reseat all contacts… | ||
| − | |||
* Neaten up wiring to the chartplotter so that the "T" lives inside the cabinet | * Neaten up wiring to the chartplotter so that the "T" lives inside the cabinet | ||
| + | |||
| + | == Electrical == | ||
| + | * High water bilge alarm should be rewired to also pump; right now if the lower switch fails the high water alarm will go off but the pump won’t run - Ted | ||
| + | * Cabin lighting -- LED and red/white option? | ||
| + | * Electrical panel -- replace LED "power on indicator" for running lights | ||
==Safety== | ==Safety== | ||
| − | *Some safety provisions for short-handed and/or night time sailing? | + | * Some safety provisions for short-handed and/or night time sailing? |
* SOP + pictures of jackline setup | * SOP + pictures of jackline setup | ||
| − | + | * Encourage all to take a Safety at Sea seminar this winter. | |
| − | *Encourage all to take a Safety at Sea seminar this winter. | + | |
* Procure 3 re-arm kits for PFDs | * Procure 3 re-arm kits for PFDs | ||
* Procure an 3rd water-activated light for 3rd throwable | * Procure an 3rd water-activated light for 3rd throwable | ||
| Line 112: | Line 137: | ||
==Mechanical== | ==Mechanical== | ||
| − | * | + | * Create a video of changing and seating washers and gaskets properly? |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
* Check engine mounts -- stbd forward seems off | * Check engine mounts -- stbd forward seems off | ||
* Odd propeller sounds at high RPM. “Rumble” that’s off and 1/s oscillation sound. | * Odd propeller sounds at high RPM. “Rumble” that’s off and 1/s oscillation sound. | ||
* Purge water out of racor | * Purge water out of racor | ||
| − | + | ||
== Spring (Pre-Launch) Tasks == | == Spring (Pre-Launch) Tasks == | ||
* Manually inflate + inspect all PFDs | * Manually inflate + inspect all PFDs | ||
* Inventory + restock med kit | * Inventory + restock med kit | ||
| + | * Go over whole hull for mold/mildew | ||
==Next summer== | ==Next summer== | ||
| Line 132: | Line 153: | ||
== Completed Tasks == | == Completed Tasks == | ||
| + | * Re-rig reefing hook to sit closer to the boom - Part is in the liquor locker drawers with a shackle on it. | ||
Revision as of 10:58, 31 October 2022
If a task needs additional explanation, please make a page for that task and post updates. When a task is completed, move it to the 'Completed Tasks' section, and include the date it was completed.
Please use the discussion page to discuss the prioritization and content of any of these tasks.
Contents
Pre-storage (fall) tasks
- Lay out all sails and look for any issues
- Wipe down all surfaces to reduce mold/mildew. (Vinegar? Peroxide? Bleach? Wood soap?)
- Remove PFDs, lines,
- Dry the spare lines, spinnakers, and anything else that’s wet, especially if they will be stored somewhere without air circulation
- Inspect all sails, lines, rig hardware, and spars before storing them for the winter
- Inspect and inventory safety gear, medical kit, etc.
- Inventory spare parts and make list of needed replacements
- Scrub bilges around engine with Joy to remove fuel leak residue
- Scrub overhead above refrigerator to remove mildew
- Remove knives -- Gavin to resharpen
- Remove all cutlery, plates, pots, etc.
Dion's Work
Centerboard
- Plan is to pull the board right away when hauled.
- Grind off head until it swings easily through wood on top of the lead keel while swelled up. Put the boat back into water to make certain it swings freely with the box wet and swollen up. Remove board again and glass up properly and install downhaul line up through the tube to the cabin top as well. New bright red paint.
- Get 1" half oval from Hamilton for Gasket Plates. Two 8' pieces... Cut to fit. Drill and counter sink for 1/4" screws on drill press. Install gasket beneath. Mark edges then, remove and re-cut gasket with hot knife. Then finally install...
Rigging, Hull, Motor
- Replace spreader lights - convert to LEDs with lower profile, mount them better. Dions
- We need a new (3rd) cowl vent, one went missing at the start of the season. Dions
- Inspect all standing rigging, grease Furlex bearings top and bottom
- All the hatch hinges need to be strengthened, replaced and/or repaired. We had water intrusion and loss of almost all of them this year (I think it was time catching up to them?) Dions
- The forward hatch teeth (the part attached to the hull that the latch goes in) needs to be re-attached. Thru bolted in bronze pls Dions
- The whole inside of the hull needs to be gone over, especially in the cockpit lockers. There was significant mold/mildew buildup. Dions in Spring?
- Scrub bilges around engine with Dawn or Joy to remove fuel leak residue
- Scrub overhead above refrigerator to remove mildew
- Create a way to hold the lid under the forepeak berth open when rummaging for supplies. Dions
- Topsides touch-up again? Re-paint next year? Check plank ends at transom, please.
- Bottom paint, What brands are best? Sea Hawk?
- Varnish- Cabin top, toe rails, coamings, tiller, companionways, hatches, spars- Interior surfaces?
- Motor- Change oil and filter. Leave spare filter on board
- Replace low-pressure engine oil line near on-engine fuel filter that has a nick and slow oil leak. It is getting worse. (+ reattach to prevent chafe; check other lines for potential chafe).
- Check forward starboard engine mount- seems off
- Polish fuel tank- Boat should arrive with less than 1/3 tank
- Purge water systems and flush/ bleach
- Fresh o rings and gaskets on fuel fill, fresh water fill and holding tank
- Flush and purge poop tank? Boat will arrive fully pumped out
- Replace or repair two bent stanchions
North Work
- We need a new canvas boot for the mast-deck connection. North.
- Two little covers for furler line port. North
- 140 work: Luff tape torn, need to buy a pre-feeder, Shorter aft batten along 140 foot
- Big red spin- tear near clew repaired
- Mainsail cover inspected and repaired as needed
Other outsource
- Code Zero - must work with current hardware. Sleeve - to fit cable.
- New #3 jib?
- Second spinnaker halyard done properly - consistent in diameter
- Replace dyneema topping lift?
MIT Work
Random Work
- Buntlines for main sail reefing (these are the lines that pass through the grommets in the sail)
- Bungees on head hatch - Gavin
- Mounting for compass? New compass?
Sails
- Working jib - bolt rope on the luff frayed near the head - maybe not needed if replacing?
Rigging
- Replace jib sheet - same diameter, length + 1' - maybe just fix?
- Whipped jib sheet ends
- Replace or end for end the main sheet
- Cunningham purchase system to easily be soft shackled on when needed - carabiner?
- Longer jib furling line to let us lead it aft? Soft shackle fairlead?
- Winches broken down and greased - Gavin
- Jib prefeeder - us
- New cable for spinnakers
- Tack line hardware for attaching spin roller furler to a jamming bight - delay for now?
- Ring-dings for turnbuckles
- Replace all cotter pins
- Double smaller block for jib halyard. - Us
Shopping List
- purchase some of those blue grippy gloves or similar for the boat to have for people to use
- Purchase more sail ties that are extra-long -- webbing -- Fran
- Procure more hand sanitizer for onboard use
- Procure more hangers for the foulies (maybe wood? or stronger plastic)
- Procure origo dometic 3000 rubber gasket for top of fuel container - https://www.atlanticmarinesupply.com/product/dometic-environmental-3880036-00-rubber-gasket/
- Procure a few more mugs for onboard use
- Procure a metric socket set for onboard tasks (e.g. engine work)
- Procure some chamois for proper clean-up
- Procure a pool noodle (or something else) for storing the battens
- Purchase new self-sealing washer for fuel stop solenoid and replace: Volvo Part 21424327
- Purchase Extra racor filters and a
Miscellaneous
- Handle to replace capstan? Get Fran a drawing
- Housing for the radar reflector—a bag or permanent hook or both
- Figure out anti-fouling for the dinghy motor (doesn't tilt far enough up to keep prop out of water).
- Anti-foul the dinghy bottom
- All the dinghy glue
- Replace eye for lee cloth on port berth
- Repair screen on the starboard porthole
- More permanent repair to companionway screen (+ better place to store)
- Replace flag on end of windex triangle
- Winch handle release issue -- can we fix this?
- Shave bilge panels for easier access?
- Grease companionway tracks
- Spruce up soundproofing around the engine
Radar and electronics
- Base for radar mount?
- Full electronics meeting to follow. Radar/new MFD, etc? Both B&G and Raymarine reps just recommended getting a new raymarine radar. To replace the MFD we’d also need to replace a lot of the sensors around the boat.
- New Raymarine radar so that we can it to display on the chart plotter?
- Get rid of gremlins in the wireless displays (voltage boost?)
- Get touchscreen physical buttons properly working
- Get a new MMSI and reprogram everything so we don't conflict with "FUSION" on the west coast? -- AIS MOB, VHF, etc.
- Engine panel electrical gremlins - clean and reseat all contacts…
- Neaten up wiring to the chartplotter so that the "T" lives inside the cabinet
Electrical
- High water bilge alarm should be rewired to also pump; right now if the lower switch fails the high water alarm will go off but the pump won’t run - Ted
- Cabin lighting -- LED and red/white option?
- Electrical panel -- replace LED "power on indicator" for running lights
Safety
- Some safety provisions for short-handed and/or night time sailing?
- SOP + pictures of jackline setup
- Encourage all to take a Safety at Sea seminar this winter.
- Procure 3 re-arm kits for PFDs
- Procure an 3rd water-activated light for 3rd throwable
- Procure a pair of safety glasses for the tool kit
Mechanical
- Create a video of changing and seating washers and gaskets properly?
- Check engine mounts -- stbd forward seems off
- Odd propeller sounds at high RPM. “Rumble” that’s off and 1/s oscillation sound.
- Purge water out of racor
Spring (Pre-Launch) Tasks
- Manually inflate + inspect all PFDs
- Inventory + restock med kit
- Go over whole hull for mold/mildew
Next summer
- Training sessions
- Skipper dry run for jacklines + MOB
Completed Tasks
- Re-rig reefing hook to sit closer to the boom - Part is in the liquor locker drawers with a shackle on it.
