Difference between revisions of "Mashnee task list"

From MITNA
Jump to: navigation, search
(Miscellaneous)
(Rigging:)
 
(154 intermediate revisions by 3 users not shown)
Line 3: Line 3:
 
Please use the discussion page to discuss the prioritization and content of any of these tasks.
 
Please use the discussion page to discuss the prioritization and content of any of these tasks.
  
== Pre-storage (fall) tasks ==  
+
==2025 Sailing Season Projects==
* Lay out all sails and look for any issues
+
* Wipe down all surfaces to reduce mold/mildew. (Vinegar? Peroxide? Bleach? Wood soap?)
+
* Remove PFDs, lines,
+
* Dry the spare lines, spinnakers, and anything else that’s wet, especially if they will be stored somewhere without air circulation
+
* Inspect all sails, lines, rig hardware, and spars before storing them for the winter
+
* Inspect and inventory safety gear, medical kit, etc.
+
* Inventory spare parts and make list of needed replacements
+
* Scrub bilges around engine with Joy to remove fuel leak residue
+
* Scrub overhead above refrigerator to remove mildew
+
* Remove knives -- Gavin to resharpen
+
* Remove all cutlery, plates, pots, etc.
+
  
== Random Work ==
 
  
* Buntlines for main sail reefing (these are the lines that pass through the grommets in the sail)
+
==2025-26 Offseason Work ==
* Repair hinges on all hatches -- Dions
+
* Bungees on head hatch - Gavin
+
* Topsides paint – if repainting isn’t on the list this year, inspect the cracks at the plank ends around the edges of the transom to make sure they aren’t holding water
+
  
== Sails==
+
Observations are listed on Discussion page
  
*140. Small hole? Luff tape broken? Need one batten.
+
===Hull and woodwork:===
 +
*Renew Bottom Paint (Dions)
 +
*Renew topsides paint (Dions)
 +
*Maintain varnish on deck structures (Dions)
 +
*Repair cracked/broken varnish on bowsprit (Dions)
 +
*Inspect dark spots under fittings at top of mast for rot (Dions)
 +
**Specifically: the spacer block under the forestay tang and the screws holding bronze strips to prevent halyard chafe
 +
*Re-bed spacer block under forestay tang: bedding is cracking around the edges (Dions)
 +
*Plane edges of soleboards/floorboards so they don't stick (Dions)
 +
*Repair/replace block on the forward hatch for the strut and reattach strut (Dion's or MIT: we can bring the hatch to the pavilion)
  
*Big Red- Repair tear near clew
+
===Sails and canvas:===
*Code Zero - must work with current hardware. Sleeve - to fit cable.
+
*Repair 95 and 160 at North
*New #3 jib?
+
*Patch working jib (MIT)
* Working jib - bolt rope on the luff frayed near the head
+
*Renew spreader patches on 160 (MIT)
 +
*Verify status of 140 and green spinnaker - are these still at North?
 +
*Replace foot battens in 160 (North)
 +
*Price out top-down furler for spinnaker
 +
*New mast boot (Libby)
  
==Rigging==
+
===Rigging:===
* Replace + test spreader lights - convert to LEDs, mount them better.
+
*End for end mainsheet (Libby)
* Second spinnaker halyard done properly - consistent in diameter
+
*Decide on replacement timeline for main halyard, topping lift, red fleck spin halyard, and spin sheets (MIT)
* Replace jib sheet - same diameter, length + 1' - maybe just fix?
+
**Probably: replace topping lift and/or main halyard (MIT - Dan)
* Replace or end for end the main sheet
+
*Repair/replace jib car pins
* Cunningham purchase system to easily be soft shackled on when needed - carabiner?
+
*Wash salt from standing rigging and inspect for rust damage (At Dion's--will Dion's do this?)
* Replace dyneema topping lift? - Dions?
+
*Thump mat or puddening for Code Zero furler (MIT)
* Longer jib furling line to let us lead it aft? Soft shackle fairlead?
+
*See if we can remove a shackle from the backstay to allow for better tensioning (MIT?)
* Winches broken down and greased - Gavin
+
*Re-seat pin holding lower end of bobstay (Dions)
* Jib prefeeder - us
+
*Inspect fitting that holds forestay to bowsprit for rust (Dions)
* Whipped jib sheet ends
+
*Add correct fitting to top of jib furler foil, to prevent wear against the stay
* New cable for spinnakers
+
* Tack line hardware for attaching spin roller furler to a jamming bight - delay for now?
+
* Ring-dings for turnbuckles
+
* Replace all cotter pins
+
* Double smaller block for jib halyard. - Us
+
* Re-rig reefing hook to sit closer to the boom - done! Part is in the liquor locker drawers with a shackle on it.
+
  
==Miscellaneous==
+
===Engine:===
* Handle to replace capstan? Get Fran a drawing
+
*Winterize engine (Dions)
* replace or repair two bent stanchions
+
*Change oil and filters (Dions)
*We need a new canvas boot for the mast-deck connection
+
*Change raw water impeller (Dions)
*Two little covers for furler line port.
+
*Change zincs (Dions)
*We need a new (3rd) cowl vent, one went missing at the start of the season
+
*High water bilge alarm should be rewired to also pump; right now if the lower switch fails the high water alarm will go off but the pump won’t run - Ted
+
*(reposting) All the hatch hinges need to be strengthened and repaired. We had water intrusion and loss of almost all of them this year (I think it was time catching up to them?)
+
*The forward hatch teeth (the part attached to the hull that the latch goes in) needs to be re-attached
+
*The whole inside of the hull needs to be gone over, especially in the cockpit lockers. There was significant mold/mildew buildup
+
*Purchase more sail ties that are extra-long -- webbing -- Fran
+
* purchase some of those blue grippy gloves or similar for the boat to have for people to use
+
* Create a way to hold the lid under the forepeak berth open when rummaging for supplies
+
* Housing for the radar reflector—a bag or permanent hook or both
+
* Figure out anti-fouling for the dinghy motor (doesn't tilt far enough up to keep prop out of water).
+
* Anti-foul the dinghy bottom
+
* Replace eye for lee cloth on port berth
+
* Replace mainsail cover - showing a lot of sun damage
+
* All the dinghy glue
+
* Anti-foul for the bottom of the dinghy engine
+
* Repair screen on the starboard porthole
+
* More permanent repair to companionway screen (+ better place to store)  
+
* Procure more hand sanitizer for onboard use
+
* Procure more hangers for the foulies (maybe wood? or stronger plastic)  
+
* Procure origo dometic 3000 rubber gasket for top of fuel container - https://www.atlanticmarinesupply.com/product/dometic-environmental-3880036-00-rubber-gasket/
+
* Procure a few more mugs for onboard use
+
* Procure a metric socket set for onboard tasks (e.g. engine work)
+
* Procure some chamois for proper clean-up
+
* Replace flag on end of windex triangle
+
* Winch handle release issue -- can we fix this?
+
  
==Centerboard==
+
===Systems:===
*Plan is to pull the board right away when hauled.
+
*Grind off head until it swings easily through wood on top of the lead keel while swelled up. Remove board again and glass up properly and install downhaul line up through the tube to the cabin top as well.
+
+
==Radar and electronics==
+
* Dions to install base for radar mount?
+
* Full electronics meeting to follow. Radar/new MFD, etc? Both B&G and Raymarine reps just recommended getting a new raymarine radar. To replace the MFD we’d also need to replace a lot of the sensors around the boat.
+
* New Raymarine radar so that we can it to display on the chart plotter?
+
* Get rid of gremlins in the wireless displays (voltage boost?)
+
* Get touchscreen physical buttons properly working
+
* Get a new MMSI and reprogram everything so we don't conflict with "FUSION" on the west coast?
+
* Electrical panel -- replace LED "power on indicator" for running lights
+
* Engine panel electrical gremlins - clean and reseat all contacts…
+
* Cabin lighting -- LED and red/white option?
+
* Neaten up wiring to the chartplotter so that the "T" lives inside the cabinet
+
  
==Safety==
+
*Fix leak in bilge pump outflow (should be within MIT capabilities)
 +
*Renew gasket/insulation around edge of the forward engine comparment/companionway stairs
 +
*Replace joker valve proactively (MIT)
  
*Some safety provisions for short-handed and/or night time sailing?
+
===Gear:===
* SOP + pictures of jackline setup
+
*New inflator for DanBuoy (got a new cartridge summer 2025; not installed)
  
*Encourage all to take a Safety at Sea seminar this winter.
+
===Admin:===
* Procure 3 re-arm kits for PFDs
+
*Renew registration for Mashnee and dinghy
 +
*Get copies of Safe Boating Certificates for all skippers to keep on boat
  
==Mechanical==
+
===Shopping List===
* Purchase new self-sealing washer for fuel stop solenoid and replace: Volvo Part 21424327
+
*Air Horns
*Polish fuel, once in Spring, once again in mid-summer. Extra racor filters and a video of changing and seating washers and gaskets properly?
+
*Purge and bleach out water systems yes
+
*Replace low-pressure engine oil line near on-engine fuel filter that has a nick and slow oil leak. It is getting worse. (+ reattach to prevent chafe; check other lines for potential chafe).
+
*Deck fill o-rings need replacing, especially for the diesel tank - https://www.wholesalemarine.com/sea-dog-o-ring-for-1-1-2-deck-fill-cap.html
+
*Procure spare oil filter
+
* Check engine mounts -- stbd forward seems off
+
* Odd propeller sounds at high RPM. “Rumble” that’s off and 1/s oscillation sound.
+
* Purge water out of racor
+
  
== Spring (Pre-Launch) Tasks ==
+
==Completed Tasks==
* Manually inflate + inspect all PFDs
+
* Inventory + restock med kit
+
  
==Next summer==
 
*Training sessions
 
* Skipper dry run for jacklines + MOB
 
  
== Completed Tasks ==
+
==Task Lists from Past Seasons==
 +
 
 +
2024-2025: [[Task_List_2024-25|here]]
 +
 
 +
2023-2024: [[Task_List_2023-24|here]]
 +
 
 +
2022-2023: [[Task_List_2022-23|here]]

Latest revision as of 09:13, 3 December 2025

If a task needs additional explanation, please make a page for that task and post updates. When a task is completed, move it to the 'Completed Tasks' section, and include the date it was completed.

Please use the discussion page to discuss the prioritization and content of any of these tasks.

2025 Sailing Season Projects

2025-26 Offseason Work

Observations are listed on Discussion page

Hull and woodwork:

  • Renew Bottom Paint (Dions)
  • Renew topsides paint (Dions)
  • Maintain varnish on deck structures (Dions)
  • Repair cracked/broken varnish on bowsprit (Dions)
  • Inspect dark spots under fittings at top of mast for rot (Dions)
    • Specifically: the spacer block under the forestay tang and the screws holding bronze strips to prevent halyard chafe
  • Re-bed spacer block under forestay tang: bedding is cracking around the edges (Dions)
  • Plane edges of soleboards/floorboards so they don't stick (Dions)
  • Repair/replace block on the forward hatch for the strut and reattach strut (Dion's or MIT: we can bring the hatch to the pavilion)

Sails and canvas:

  • Repair 95 and 160 at North
  • Patch working jib (MIT)
  • Renew spreader patches on 160 (MIT)
  • Verify status of 140 and green spinnaker - are these still at North?
  • Replace foot battens in 160 (North)
  • Price out top-down furler for spinnaker
  • New mast boot (Libby)

Rigging:

  • End for end mainsheet (Libby)
  • Decide on replacement timeline for main halyard, topping lift, red fleck spin halyard, and spin sheets (MIT)
    • Probably: replace topping lift and/or main halyard (MIT - Dan)
  • Repair/replace jib car pins
  • Wash salt from standing rigging and inspect for rust damage (At Dion's--will Dion's do this?)
  • Thump mat or puddening for Code Zero furler (MIT)
  • See if we can remove a shackle from the backstay to allow for better tensioning (MIT?)
  • Re-seat pin holding lower end of bobstay (Dions)
  • Inspect fitting that holds forestay to bowsprit for rust (Dions)
  • Add correct fitting to top of jib furler foil, to prevent wear against the stay

Engine:

  • Winterize engine (Dions)
  • Change oil and filters (Dions)
  • Change raw water impeller (Dions)
  • Change zincs (Dions)

Systems:

  • Fix leak in bilge pump outflow (should be within MIT capabilities)
  • Renew gasket/insulation around edge of the forward engine comparment/companionway stairs
  • Replace joker valve proactively (MIT)

Gear:

  • New inflator for DanBuoy (got a new cartridge summer 2025; not installed)

Admin:

  • Renew registration for Mashnee and dinghy
  • Get copies of Safe Boating Certificates for all skippers to keep on boat

Shopping List

  • Air Horns

Completed Tasks

Task Lists from Past Seasons

2024-2025: here

2023-2024: here

2022-2023: here