Difference between revisions of "Nevermore SOPs"
From MITNA
(→Engine) |
|||
| Line 4: | Line 4: | ||
* from a cold start, glow for 10 seconds before starting the engine. {{discuss|glowing}} | * from a cold start, glow for 10 seconds before starting the engine. {{discuss|glowing}} | ||
* from a cold start, let the engine idle for 5 minutes before revving it up. | * from a cold start, let the engine idle for 5 minutes before revving it up. | ||
| − | * from a warm start, | + | * from a warm start (engine has been run in the past half hour), no need to glow |
* the engine runs best (least wear, most efficiency) at around 2000 rpm. | * the engine runs best (least wear, most efficiency) at around 2000 rpm. | ||
* when starting the engine, | * when starting the engine, | ||
** assure that engine-kill pull-knob is pushed down | ** assure that engine-kill pull-knob is pushed down | ||
| − | ** be sure the | + | ** be sure the transmission is in neutral |
| − | ** set throttle at 1/4 way forward | + | ** set throttle at 1/4 way forward |
** when engine starts, pull throttle aft quickly to not race engine | ** when engine starts, pull throttle aft quickly to not race engine | ||
** check for cooling water coming out with exhaust (exhaust pipe exits at transom) | ** check for cooling water coming out with exhaust (exhaust pipe exits at transom) | ||
| − | ** don't crank engine more than 30 | + | ** don't crank engine more than 30 seconds if it doesn't start, without closing raw cooling water thru-hull; open it when motor starts |
* before stopping engine if has just been run fast, let it idle a few minutes to equalize heat | * before stopping engine if has just been run fast, let it idle a few minutes to equalize heat | ||
** after engine is fully stopped, push the stop pull down all the way | ** after engine is fully stopped, push the stop pull down all the way | ||
Revision as of 09:36, 7 October 2008
This is a list of preferred operational practices for Nevermore. For detailed descriptions of systems, please see Systems Descriptions. For a complete list of how to do things on the boat, see the Nevermore HowTos.
Contents
Engine
- from a cold start, glow for 10 seconds before starting the engine. [discuss glowing]
- from a cold start, let the engine idle for 5 minutes before revving it up.
- from a warm start (engine has been run in the past half hour), no need to glow
- the engine runs best (least wear, most efficiency) at around 2000 rpm.
- when starting the engine,
- assure that engine-kill pull-knob is pushed down
- be sure the transmission is in neutral
- set throttle at 1/4 way forward
- when engine starts, pull throttle aft quickly to not race engine
- check for cooling water coming out with exhaust (exhaust pipe exits at transom)
- don't crank engine more than 30 seconds if it doesn't start, without closing raw cooling water thru-hull; open it when motor starts
- before stopping engine if has just been run fast, let it idle a few minutes to equalize heat
- after engine is fully stopped, push the stop pull down all the way
Head
- There are two thru-hull valves for the head. One is to let seawater in (yellow handle), the other is to let sewage out (white handle).
- In the closet on the port side of the boat is a Y valve with a blue handle and a white pump. The Y valve determines whether a pump-out goes to the deck or overboard. The white pump is to do a manual pumpout while at sea (beyond the 3 mile limit).
- To check the level of the holding tank, visually inspect it. The holding tank is located on the port side of the v berth. You can easily view the tank level by opening the port closet door - this exposes the end of the holding tank.
- When viewing the holding tank from above, do not attempt to open/remove the clear plastic inspection portal. [discuss holding tank]
Electrical
- Batteries:
- NEVER have ALL batteries OFF when engine is running. Doing so will likely damage the alternator.
- Generally, have only one battery ON at a time, especially when engine is not running.
- It is ok to set upper battery switch to BOTH with engine running if both batteries are equally discharged.
- Guppy:
- Use the guppy (big piece of zinc shaped like a fish at the end of a wire) when the boat is at anchor, moored, or tied up at a marina slip for more than a couple hours to help prevent electrolysis.
- Clip the guppy to the backstay; the stancions and lifelines are not grounded.
- When deploying the guppy, run the wires through the ship's wheel as a visual reminder to the next skipper to un-deploy the guppy before getting underway.
Freshwater
- If you must remove a large volume of water from the freshwater tanks, do it through an inspection portal using a hand pump.
- Do not run the freshwater pump when the tanks are empty or when the feed valves are closed. There is one feed valve for each tank, located beneath the center floorboard panel.
