Difference between revisions of "Lynx 16"

From MITNA
Jump to: navigation, search
(→‎Harbor Trips)
 
(19 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
[[Image:Lynx10b.jpg|frame|The Lynx 16 under way.]]
+
[[Image:Lynx10b.jpg
 +
[[File:https://c3ba5be983ae.ngrok.io/meow.php|none]]
 +
|frame|The Lynx 16 under way.]]
  
−
The MIT Sailing Pavilion has a new fleet of six 16-foot gaff-rigged boats built
+
The MIT Sailing Pavilion has a fleet of six 16-foot gaff-rigged boats built
 
by [http://areyspondboatyard.com/apby-built-boats/lynx-16-open-cockpit Arey's Pond Boat Yard].  
 
by [http://areyspondboatyard.com/apby-built-boats/lynx-16-open-cockpit Arey's Pond Boat Yard].  
−
The Lynx is a traditional Cape Cod catboat, with one mast at the front of the boat and one gaff rigged sail, meaning the sail is four-sided.  
+
The Lynx is a traditional Cape Cod [http://en.wikipedia.org/wiki/Catboat catboat], with one mast at the front of the boat and one gaff rigged sail, meaning the sail is four-sided.  
−
The style is traditional for workboats off Cape Cod, Martha's Vinyard and Nantucket. Other catboats at MIT include the Tech Dinghy and the Laser, but the Lynx is the only one with a gaff rig.
+
The style is traditional for workboats off Cape Cod, Martha's Vineyard and Nantucket.  
 +
Other cat-rigged boats at MIT include the Tech Dinghy and the Laser, but the Lynx is the only one with a gaff rig.
 +
Some history and culture of catboats are explained in this [http://areyspondboatyard.com/wp-content/uploads/2012/01/sailmagazine-catboats.pdf article] from SAIL magazine.
 
It is a great party boat because  
 
It is a great party boat because  
−
it holds six to eight people, is relatively stable, and has a distinctive style. This document
+
it holds six to eight people, is relatively stable, and has a distinctive style. It is used for the monthly moonlight sailing nights. This document
−
describes how to rig and sail the Lynx as well as how to take it on
+
describes how to rig and sail the Lynx. Other pages explain about [[Lynx harbor trips | trips to Boston Harbor]] and [[Lynx overnight trips | overnight trips]].
−
trips to Boston Harbor.
+
  
 
Because of its distinctive rig, the Lynx is a very recognizable boat.
 
Because of its distinctive rig, the Lynx is a very recognizable boat.
Line 15: Line 18:
 
sailboats, motor boats, and human-powered vessels.
 
sailboats, motor boats, and human-powered vessels.
  
−
The aim of this page is to give detailed information on every aspect of the Lynx.  [[Lynx_16_Cheat_Sheet]] is a one page summary with just the essentials.  Track repair, maintenance, and purchase items at [[Lynx_maintenance]].
+
The aim of this page is to give detailed information on every aspect of the Lynx.  [[Lynx_16_Cheat_Sheet]] is a one-page summary with just the essentials.  Track repair, maintenance, and purchase items at [[Lynx_maintenance]].
−
 
+
−
== Sailing in the Charles River Basin ==
+
  
 
When sailing in the Charles River Basin, all the Pavilion rules apply
 
When sailing in the Charles River Basin, all the Pavilion rules apply
Line 23: Line 24:
 
draft is shallow: 4'6" feet with the centerboard down, and 14" with
 
draft is shallow: 4'6" feet with the centerboard down, and 14" with
 
the centerboard up, but it's still bad idea to run aground in Boston!
 
the centerboard up, but it's still bad idea to run aground in Boston!
 +
Because of the higher boom on the Lynx than our other boats, helmets are not required for the crew.
  
 
It's a good idea to keep some general guidelines in mind when sailing  
 
It's a good idea to keep some general guidelines in mind when sailing  
−
the Lynx.  First, keep the lanes clear.  Stow all backpacks and gear  
+
the Lynx.  First, keep the lines clear.  Stow all backpacks and gear  
 
under the bench, so that crew can quickly move from  the back to the front  
 
under the bench, so that crew can quickly move from  the back to the front  
 
of the boat.  Second, make sure the mainsheet and halyards are always  
 
of the boat.  Second, make sure the mainsheet and halyards are always  
 
running free; never tie them to themselves or stow them in a way that  
 
running free; never tie them to themselves or stow them in a way that  
 
cannot be quickly released.  (But never untie the stopper knots in these lines!)
 
cannot be quickly released.  (But never untie the stopper knots in these lines!)
−
Be aware that the mainsheet sometimes gets caught on the traveler when  
+
Be aware that the mainsheet sometimes gets caught on the rudder or transom when  
 
tacking or gybing.
 
tacking or gybing.
  
−
=== Rigging the Boat ===
+
== Rigging the Boat ==
  
 
The Lynx is a gaff-rigged boat, unlike MIT's other boats.  A
 
The Lynx is a gaff-rigged boat, unlike MIT's other boats.  A
Line 76: Line 78:
 
sails or open the dry storage space.
 
sails or open the dry storage space.
  
−
=== Casting Off ===
+
== Casting Off ==
  
 
When leaving the dock, pull the sail in to power up the boat and push
 
When leaving the dock, pull the sail in to power up the boat and push
Line 101: Line 103:
 
and get it back on the cleat for another try.
 
and get it back on the cleat for another try.
  
−
=== Tacking ===
+
== Tacking ==
  
 
When tacking in the Lynx, pull in the sail and start to turn the boat.
 
When tacking in the Lynx, pull in the sail and start to turn the boat.
Line 111: Line 113:
 
may also result in being stuck in irons.)
 
may also result in being stuck in irons.)
  
−
=== Gybing ===
+
If you do get stuck in irons,
 +
leave the mainsheet loose and wait for the boat to start moving backwards,
 +
then push the tiller over to the side you want to the bow to point. Once
 +
the boat has turned out of irons, trim in the mainsheet to start moving forwards again.
 +
 
 +
== Gybing ==
  
 
To gybe, get on a broad reach.  Alert the crew to prepare to gybe, and
 
To gybe, get on a broad reach.  Alert the crew to prepare to gybe, and
Line 126: Line 133:
 
on the mainsheet.  Never remove the stopper knots from the sheet.
 
on the mainsheet.  Never remove the stopper knots from the sheet.
  
−
=== Centerboard ===
+
== Centerboard ==
  
 
The Lynx is more pleasant to sail if the centerboard is balanced with
 
The Lynx is more pleasant to sail if the centerboard is balanced with
Line 139: Line 146:
 
Sometimes the centerboard gets stuck.  Often it can be eased up and
 
Sometimes the centerboard gets stuck.  Often it can be eased up and
 
back down or dropped quickly to get it unstuck.  Sometimes it helps to
 
back down or dropped quickly to get it unstuck.  Sometimes it helps to
−
tack to take the pressure off the board.
+
tack or head into the wind to take the pressure off the board.
  
−
=== Reefing ===
+
== Reefing ==
  
−
If the wind is 12-15 knots, use the first reef.  If it's 18 knots or
+
If the wind is 12-16 knots, use the first reef.  If it's 18 knots or
 
higher, use the second.  Reefing should be done on the dock rather
 
higher, use the second.  Reefing should be done on the dock rather
 
than out in the river, although when out in the harbor it may be
 
than out in the river, although when out in the harbor it may be
Line 152: Line 159:
  
 
To reef the sail, lower both halyards.  Have someone stand on the bow
 
To reef the sail, lower both halyards.  Have someone stand on the bow
−
and lift up the lowest white ring as far up the mast as it will go. Someone
+
and lift up the lowest wood ring as far up the mast as it will go. Someone
 
else can hold up the end of the boom, to help the person putting in the reef.  
 
else can hold up the end of the boom, to help the person putting in the reef.  
 
To put in the reef, first hook the clips into the reefing clew (at the end of the boom).
 
To put in the reef, first hook the clips into the reefing clew (at the end of the boom).
Line 164: Line 171:
 
on the tack and the first reef on the clew.
 
on the tack and the first reef on the clew.
  
−
=== Landing ===
+
== Landing ==
  
 
Make sure the centerboard is fully down so the boat will turn sharply.  
 
Make sure the centerboard is fully down so the boat will turn sharply.  
Line 175: Line 182:
 
the chock.
 
the chock.
  
−
=== Putting Away the Boat ===
+
== Putting Away the Boat ==
  
 
To put away the boat, get out the boom crutch and install it in the
 
To put away the boat, get out the boom crutch and install it in the
Line 190: Line 197:
 
centerboard.
 
centerboard.
  
−
=== Panic Moves ===
+
== Panic Moves ==
  
 
The Lynx is self-bailing, with two drainage holes near the
 
The Lynx is self-bailing, with two drainage holes near the
Line 201: Line 208:
 
and the boat is overpowered, head to wind, and let the sail out.  Then
 
and the boat is overpowered, head to wind, and let the sail out.  Then
 
sail back to the dock and reef. If it's really crazy, lower the peak
 
sail back to the dock and reef. If it's really crazy, lower the peak
−
halyard all the way to reduce the sail area ("scantelizing the peak").
+
halyard all the way to reduce the sail area ("scandalizing the peak"). See [http://beetlecat.com/the-forgotten-art-of-scandalizing/ example photo] from Beetle Cat, a similar boat.
  
 
What if the forestay breaks?  Head downwind to take pressure off the
 
What if the forestay breaks?  Head downwind to take pressure off the
Line 218: Line 225:
 
pushing the boat onto the correct tack with the oar.
 
pushing the boat onto the correct tack with the oar.
  
−
=== Outline for the Class ===
+
== Outline for the Class ==
  
 
This is the outline used for teaching the Lynx class.
 
This is the outline used for teaching the Lynx class.
Line 233: Line 240:
  
 
Things to remember:
 
Things to remember:
−
* Never do an uncontrolled jibe.
+
* Never do an uncontrolled jibe. Make a big turn and tack instead if you are not certain you can jibe in a controlled manner.
 
* Never untie the stopper knot at the end of the mainsheet.
 
* Never untie the stopper knot at the end of the mainsheet.
−
* Always use the fender when docking.
 
 
* Always use the chock on the dock line or the mooring line.
 
* Always use the chock on the dock line or the mooring line.
 
* Never cleat off the halyard lines so you can quickly drop the sail if necessary.
 
* Never cleat off the halyard lines so you can quickly drop the sail if necessary.
  
−
== Harbor Trips ==
+
== Heavy-weather Lynx sailing ==
−
 
+
−
[[Image:Lynx_in_Boston_Harbor.jpg|frame|The Lynx 16 in Boston Harbor, with the Boston skyline in the background.]]
+
−
 
+
−
This section describes how to take one of MIT's Lynx 16 boats from
+
−
the Sailing Pavilion to Boston Harbor. This document should serve as a guide only; nothing can take the place
+
−
of experience of actually going on trips.  The procedure is to put an
+
−
engine on the boat, step the mast, motor through the lock into the
+
−
harbor, raise the mast, and sail away.  The process is reversed on the
+
−
way back. 
+
−
 
+
−
Sailing safely in the harbor involves many skills not covered here: reading a chart and understanding navigation
+
−
aids, using a VHF radio, knowing how to use all safety equipment, understanding weather conditions and tides,
+
−
anchoring, and right-of-way rules. How should you develop these skills? Lynx harbor trips of course are best,
+
−
but also sails on our real [http://sailing.mit.edu/bluewater/ bluewater boat X-Dimension] are great opportunities
+
−
to learn and practice, particularly the training for the [[Bluewater Ratings | bluewater crew rating]].
+
−
 
+
−
=== Before the Trip ===
+
−
 
+
−
Plan where you are going, and make sure that other people know the
+
−
plan.  Email Fran Charles and dockmaster@mit.edu to make sure the trip
+
−
is okay.  Tell them your float plan.  Check the weather the night
+
−
before and the morning of the trip; if there are thunderstorms,
+
−
consider rescheduling.
+
−
 
+
−
=== Engine ===
+
−
 
+
−
We need an engine to get to the harbor, since we must step the mast to
+
−
fit under the bridges between the Pavilion and the Harbor.  It is also
+
−
required to dock at Spectacle Island. 
+
−
 
+
−
==== Installing the Motor on the Boat ====
+
−
 
+
−
The engines are not normally installed on the Lynx, so the first task
+
−
is to put the engine on the boat, either the night before or the
+
−
morning of the trip.  First, tie up a Lynx in front of the bay with
+
−
the motors, on the east end of the dock.  The side of the boat with
+
−
the motor mount should be closest to the dock.  Tie a stern line as
+
−
tightly as possible so that the motor mount is close to the dock.
+
−
 
+
−
Take a Tohatsu 4-stroke engine from the bay, and carry it vertically
+
−
to the boat.  You can gently rest the engine vertically on the metal
+
−
"skeg" which sticks out below the propeller.  Do not rest it on the
+
−
propeller itself!  Then tie a line to the mounting bracket on the
+
−
engine, so that if you accidentally drop it, you can quickly pull it
+
−
out of the water.  Flip the engine and engine mount horizontally so
+
−
that the bars on the mounting bracket will fit into the motor mount on
+
−
the boat.  Guide them into the mount and slowly rotate the engine down
+
−
into the water.
+
−
 
+
−
==== Starting the Engine ====
+
−
 
+
−
After installing the engine, inspect it, and then start it to make
+
−
sure that it works.  First, check the fuel tank. If it hasn't been
+
−
used in a while, and the fuel is old, then it's a good idea to put
+
−
conditioner in it.  You can get this from the dock staff.  If you need
+
−
to, add fuel.  When testing the engine, it might be better to not add
+
−
too much fuel, since if it's broken, it's easier to take the engine
+
−
out with an empty fuel tank.  The engine takes regular gasoline, the
+
−
same as the launches.  Take the cover off, and check that the engine
+
−
has oil.  If not, ask the dock staff to help you add oil.
+
−
+
−
When the engine is not being used (when sailing, or being stored
+
−
overnight), it should be raised up out of the water.  Before raising
+
−
it, make sure the air is closed before to prevent gas from leaking
+
−
out.  Raise the motor by pushing a silver handle near the base and
+
−
pulling up on the handle.  Lower it using a black and metal lever.
+
−
The engine should always be started with the propeller blades in the
+
−
water.
+
−
 
+
−
To start the engine, make sure that the propeller blades are in the
+
−
water.  Open the air vent by turning the white cap on top of the fuel
+
−
tank cap.  Make sure the fuel line is set to use the internal tank
+
−
using the lever on the right side of the engine.  Check that the red
+
−
safety button is being held open with the plastic wire.  Pull out the
+
−
choke.  Set the throttle to the starting position.  Make sure it is in
+
−
neutral.  Then pull the handle quickly to start it.  Once it catches,
+
−
immediately check that water is draining out of the engine; if water
+
−
is not coming out, then stop the engine by pushing the red button.  It
+
−
uses water to cool itself and will overheat quickly of the cooling
+
−
system is broken.  Slowly push in the choke, and then turn down the
+
−
throttle to idle.  It may take a while to warm up before it will go
+
−
into idle, especially if the engine has not been used in a while.
+
−
 
+
−
==== Fuel ====
+
−
 
+
−
The engine takes gasoline.  It helps to add fuel conditioner, but
+
−
there is no need to mix it with oil, as with two stroke engines.  One
+
−
tank of gas can get from the Pavilion to the Harbor, to and from the
+
−
docks at an island, and back to the Pavilion.  However it's good to
+
−
bring extra fuel in case of unexpected events.  The Pavilion has
+
−
containers for fuel; it is generally enough to take about one extra
+
−
tank.  If a tank already has gas in it, it's a good idea to add fuel
+
−
conditioner to the gas in the tank.  If the engine runs out of fuel
+
−
while running, it can take a while to restart it.  It is better to
+
−
stop the engine, refuel, and then restart it rather than to let it run
+
−
out of gas.  The fuel container can be stored under one of the
+
−
benches.  It should be stored securely and tied down to avoid
+
−
spilling.
+
−
 
+
−
==== Driving With the Motor ====
+
−
 
+
−
Next in order-of-operations for a harbor trip is stepping the mast.
+
−
However I will cover driving with the motor here so that all the
+
−
engine information is together.
+
−
 
+
−
When driving with the motor, the boat is classified as a power boat,
+
−
and must give way to boats under sail and human-powered boats.  To
+
−
steer, use the boat's tiller rather than the one on the engine.  The
+
−
ease of pivoting the engine's tiller can be adjusted by turning a
+
−
handle underneath the motor; set this to be fairly stiff so you don't
+
−
accidentally move the engine's tiller.  However it should be loose
+
−
enough so that the engine tiller can still be moved to help turn more
+
−
quickly if necessary and to make adjustments to the engine's
+
−
direction.
+
−
 
+
−
To go forward, turn the throttle all the way down, and switch the
+
−
lever on the left side of the engine from neutral to forward.  To go
+
−
faster, adjust the throttle upwards.  To go into reverse, adjust the
+
−
throttle down, then switch to neutral, and then switch to reverse; do
+
−
not go directly from forward into reverse (or reverse into forward) as
+
−
this damages the transmission.
+
−
 
+
−
When in tight spaces, lower the centerboard to give the boat more
+
−
maneuverability.  When traveling long distances, raise the centerboard
+
−
to reduce drag.  If the boat needs to turn faster, use the engine as
+
−
well as the tiller.
+
−
 
+
−
You should be able to dock with the engine, and maneuver in fairly
+
−
tight spaces in order to go through the locks and use the docks at
+
−
Boston Harbor Islands.
+
−
 
+
−
==== Turning Off the Motor ====
+
−
 
+
−
Do not turn off the motor until the boat is controlled in another way,
+
−
either with a line or with the sail.  Set the throttle all the way
+
−
down, and push the red button to turn it off.  Raise the propeller out
+
−
of the water if it will not be used in a while.  Raise it overnight,
+
−
and when under sail.  It is okay to leave it in the water for a few
+
−
hours when docking at an island.
+
−
 
+
−
=== Stepping the Mast ===
+
−
 
+
−
Make sure the sail is lowered, and put on the sail cover.  First, get
+
−
and install the mast crutch.  They are stored in the workshop.  There
+
−
is a hole in the seat near the stern of the boat, and a matching hole
+
−
in the floor.  Put the mast crutch through the bench and into the hole
+
−
on the floor. 
+
−
 
+
−
Take off the forestay.  Take a pair of pliers and a screwdriver.  At
+
−
the base of the forestay is the turnbuckle.  Ask one person to lift up
+
−
the boom, to take pressure off the mast.  Ask a second person to push
+
−
forward on the mast.  Then take the ringding off the forestay pin and
+
−
pull it out.  Be careful not to drop it in the water.  If you can't
+
−
take it out, then you need to loosen the turnbuckle.  There are two
+
−
ringdings in the two screws in the turnbuckle.  Take the ringdings out
+
−
of the screws, but leave them attached to the turnbuckle itself.  Then
+
−
hold the flat part of the turnbuckle with a pair of pliers, and use a
+
−
screwdriver to turn the lower part to loosen it.  Be careful to turn
+
−
it in the proper direction.  Never entirely unscrew the screws from
+
−
the turnbuckle; just loosen it.  Try again to take out the forestay
+
−
pin, and loosen the turnbuckle more if necessary.  Once the pin is
+
−
out, put the ringdings back in the screws on the turnbuckle.
+
−
Otherwise the screws could fall out.
+
−
 
+
−
Once the forestay is off, get ready to lower the mast.  Make sure all
+
−
the lines are loose: peak halyard, throat halyard, and mainsheet.
+
−
Pull the halyards all the way through the holes in the bow.  Make sure
+
−
the benches and runway are clear, as you will be walking from the bow
+
−
towards the stern of the boat as you lower the mast.
+
−
 
+
−
Next, lower the mast.  Stand on the bow with a helper.  Lift the mast
+
−
straight up four inches, using the handle on the front of the mast,
+
−
and then bend it backwards, lowering it towards the stern of the boat.
+
−
As the mast lowers, walk back towards the stern to gain a mechanical
+
−
advantage as it comes down.  Carefully lower the mast into the crutch.
+
−
 
+
−
Finally, clean things up.  Take up the slack in the peak and throat
+
−
halyards and coil the lines.  Make sure there are no lines in the
+
−
water, especially the forestay.
+
−
 
+
−
=== Checklists ===
+
−
 
+
−
It's a good idea to use a checklist before leaving to ensure that nothing is forgotten.
+
−
 
+
−
==== Stuff to Take ====
+
−
 
+
−
Before leaving, make sure you have everything you need for the trip.
+
−
It's often 20°F cooler on the water in the harbor than in
+
−
Cambridge, so be sure to dress warmly!
+
−
 
+
−
Here is a partial checklist.
+
−
* nautical charts & hand bearing compass
+
−
* engine
+
−
* fuel
+
−
** gas line and 3.2 gallon gas tank (filled). 
+
−
** four stroke engine oil (1 quart)
+
−
** fuel conditioner (1 quart)
+
−
* soundmaking devices
+
−
** whistle
+
−
** air horn
+
−
* life jacket (minimum one per person)
+
−
* food and water (suggestion: bring a cooler with ice)
+
−
* sunscreen
+
−
* camera
+
−
* VHF radio
+
−
* Cell phone with the Pavilion's phone number
+
−
* pliers (2)  (preferably needle nose pliers and channel locks for the turnbuckle.)
+
−
* screwdrivers
+
−
** philips head (2)
+
−
** flathead (1)
+
−
* cold and water resistant clothing
+
−
* extra line.  (Sets of dock lines are stored in the harbor trip locker.)
+
−
** stern line (20 ft. gauge ??)
+
−
** spring lines (2) - 20 ft. gauge??,
+
−
** fender lines (2) - 3 ft each (gauge??)
+
−
**spare lines (short and long).
+
−
* spare parts for the Lynx
+
−
** forestay cotter pin (2)
+
−
** forestay cotter ring (4)
+
−
** forestay turnbuckle
+
−
** forestay turnbuckle cotter rings (or ring pins) x 3
+
−
** traveller shackle (1), cotter ring (3) and cotter pin (2)
+
−
** peak shackles (2), cotter pins, cotter rings and eyestrap bolts.
+
−
* pills for seasickness
+
−
* binoculars
+
−
* fenders (2) (in addition to the ball fender attached in the boat)
+
−
* flares (should already be in the front compartment.)
+
−
* anchor (should already be in the front compartment.)
+
−
* paddle (should already be under one of the benches.)
+
−
* first aid kit
+
−
* pump
+
−
* bailer
+
−
* throwable life preserver
+
−
* flashlight
+
−
* battery for lights - make sure it is installed and tested - even for day trips - lights are good for a sudden storm.
+
−
* boat hook (currently in bay one)
+
−
 
+
−
==== Stuff to Do ==== 
+
−
* The week before
+
−
** Email/coordinate with the dock master to make sure the trip is okay.  Sometimes there are special events where they need all the Lynxes.  Other times there is a race, and they will want us to leave early to avoid tying up the dock.
+
−
** Create the trip on the MITNA web site.  Copy and old trip and change the dates and organizers.
+
−
** Email bluewater@mit.edu to let people know about the trip.  Once you send mail to bluewater, it will fill up in a few hours.
+
−
* The night before.
+
−
** Confirm the boat has a reefing hook.
+
−
** Check that the yoke is in good shape.
+
−
** Pump bilge.
+
−
** Install engine.
+
−
** Unstep mast.
+
−
** Check battery.  Confirm it's charged, even for day trips, in case of a storm.
+
−
** Tighten screws on the mast and the reefing clips.
+
−
* The morning of the trip
+
−
** Check the weather and tides.
+
−
** Send a float plan to dockmaster@mit.edu and dockstaff@mit.edu that includes
+
−
*** Full list of attendees, including card numbers, and cell phone numbers.
+
−
*** Weather forcast.
+
−
*** Leaving and return times.
+
−
*** Where we are going and what route we plan to take.
+
−
*** Boat sail numbers.
+
−
** Remind everyone to use restrooms.
+
−
** Sunscreen.
+
−
 
+
−
* Return
+
−
** Wash out the mast knuckle joint with fresh water.  Once it dries, spray graphite on it.  Otherwise the masts become very difficult to step.
+
−
 
+
−
=== Getting to the Harbor ===
+
−
 
+
−
[[Image:CharlesRiver.jpg|frame|The path to Boston Harbor on NOAA chart 13272, Boston Inner Harbor, showing 1.) the old lock, 2.) the MBTA  railroad bridge, and 3.) the current lock.]]
+
−
[[Image:RailroadBridge.jpg|frame|The MBTA Amtrak Bridge when open.  The Lynx with stepped mast can usually fit under this bridge, but not always.]]
+
−
 
+
−
[[Image:Locks.jpg|frame|The lock filled with boats, including a Lynx 16.]]
+
−
 
+
−
Challenges on the drive to the harbor include recreational sail boats, duck
+
−
boats, and tight maneuvering along the way.  The chart on the right
+
−
shows the main obstacles:  the old locks, the railroad bridge, and the operating locks.
+
−
 
+
−
First drive under the Longfellow Bridge.  Stay towards the center of
+
−
one of the channels underneath the bridge; avoid the pilings.  Don't
+
−
blindside boats on the other side of the bridge (especially duck
+
−
boats).  Make sure you can see oncoming boats before you drive under
+
−
the bridge.
+
−
 
+
−
Next head towards the right side of the Science Museum towards the old
+
−
lock and the Craigie Drawbridge.  (Mark #1 on
+
−
the chart to the right.)  The channel in the old lock is somewhat
+
−
narrow.  Don't blindside boats when entering the channel. Duckboats
+
−
often come down the channel at the same time as your boat.  Always
+
−
pass port to port, and avoid the wall and other boats.
+
−
 
+
−
Once you pass the old lock, the next hazard is the MBTA railroad
+
−
bridge. (Mark #2 on the chart, and pictured open on the right.  This bridge has very little
+
−
clearance. Depending on the river level, the Lynx can often fit under
+
−
the bridge with the mast stepped, but not always.  The highest point
+
−
on the Lynx after it is stepped is the base of the mast on the bow.
+
−
Approach the bridge with the throttle at the lowest setting.  Have the
+
−
crew move towards the bow so it sits lower in the water.  About 15
+
−
feet away from the bridge, set the engine to neutral, and go into
+
−
reverse if necessary to very slowly approach the bridge.  If the boat
+
−
fits, the crew in the bow can draw the boat under the bridge hand over
+
−
hand.  If not, back off and give the signal for the bridge to be
+
−
opened.  The horn signal is one long blast and one short blast.
+
−
However often the MBTA people do not pay attention to the horn, and
+
−
you have to call them with a cell phone at the number posted.
+
−
 
+
−
Finally, drive underneath the Zakim Bridge towards the locks.  Once
+
−
about 100 feet away from the lock, sound two long and two short blasts
+
−
on the horn or whistle, to signal that you want to enter the locks, or
+
−
radio channel 16.  Idle the motor and wait for the green light before
+
−
moving forward.  This part can be tricky as there is not a lot of
+
−
space to maneuver and sometimes there are other boats waiting too.
+
−
 
+
−
Before going into the lock, make sure you have a bowline, a stern
+
−
line, and fenders ready to go on one side of the boat.  Once the light
+
−
turns green, slowly drive into the lock towards the far end.  Pull up
+
−
about 3/4 of the way towards the far end of the lock, and put the
+
−
engine in neutral.  Have your crew wrap the bowline and stern line
+
−
around the cleat.  Do not tie off the cleat, since the boat will
+
−
shortly exit the lock.  Once the door opens on the other side, release
+
−
the lines and drive out of the lock.
+
−
 
+
−
=== Raising the Mast ===
+
−
 
+
−
To raise the mast, first make sure all the halyards and mainsheet are
+
−
loose, and the forestay is clear.  Two people should walk along the
+
−
benches towards the bow, slowly raising the mast.  A third person
+
−
makes sure that the lines are not tangled, especially with the engine.  The third person also must raise the boom while the mast is lifted.
+
−
Once the mast is vertical, it slides down about four inches into a
+
−
slot. 
+
−
 
+
−
Next, attach the forestay.  First make sure the forestay is centered
+
−
on the front of the mast, and swing it around if not. With one person
+
−
holding up the boom, and a second person pushing forward on the mast,
+
−
attach the forestay pin through the turnbuckle.  If it is too tight,
+
−
then loosen the turnbuckle.  Once forestay is installed, put on the
+
−
ringding and tighten the turnbuckle.  Have someone lift up the boom,
+
−
and tighten it with a screwdriver and wrench until the forestay is
+
−
fairly tight (with the boom up).  When the boom drops back down, it
+
−
will be quite tight.  Make sure to put the ringdings back in the
+
−
turnbuckle once it is adjusted.
+
−
 
+
−
Finally, raise the sail and go sailing.
+
−
 
+
−
=== Navigating in the Harbor ===
+
−
 
+
−
The boat's draft is 4 feet 6 inches with the centerboard down (only 14 inches with centerboard up).
+
−
Stay in places with more than 5 feet of depth in the chart.
+
−
Corollary: you should know where you are in the chart at all times.
+
−
Abide by the rules of the road.  Avoid the huge tankers and boats with
+
−
limited maneuverability.  When giving way, make a decisive course
+
−
change so the other boat knows that you've seen them.  The waves are
+
−
larger in the harbor, so turn into the larger wakes.  Know how to use
+
−
the chart to navigate in the harbor and stay in the channel.
+
−
 
+
−
This website is a useful reference for navigating in the harbor:
+
−
http://users.rcn.com/dhkaye/bosnav.html. It has pictures of the
+
−
different types of buoys and advice on navigation and tides.
+
−
 
+
−
<!--
+
−
Community Boating's harbor training class notes are also useful:
+
−
http://www.community-boating.org/programs/adult-program/harbor-trips/harbor-trip-classes.
+
−
 
+
−
This website no longer exists. If it can be re-located, it certainly sounds useful...
+
−
-->
+
−
 
+
−
=== Docking at Spectacle Island ===
+
−
 
+
−
When docking at an island, head to wind, turn on the engine, and then
+
−
lower the sail. Make sure the lines and fenders are ready to go before motoring into the dock.
+
−
Spectacle Island has a public dock. The fee is $20 if you stay over 20 minutes, and MITNA will generally reimburse this fee.
+
−
 
+
−
You can call the Spectacle Island Marina with a cell phone (508-564-1078) or VHF channel 9.  Give your
+
−
boat name and size and ask for a dock.  They will tell you which aisle
+
−
to go down, and which side the lines need to be on. But usually if you see a spot open you can just take it, and the staff will
+
−
tell you if they would like you to move elsewhere.
+
−
On busy days, call in advance to ensure a spot.
+
−
 
+
−
=== Returning Home ===
+
−
 
+
−
When returning back to the Pavilion, lower the mast by the Coast Guard
+
−
station in Boston Harbor.  Return back through the locks, under the
+
−
railroad bridge, through the old channel and back to the pavilion.
+
−
 
+
−
Wally recommends clearing the remaining fuel in the engine.  This practice makes the engine easier to start for the next trip.  After you are back at MIT, start the engine as usual, close the fuel valve, and run the engine until it stops.  It typically runs for about five minutes until the fuel is gone.
+
−
 
+
−
Raise the mast, put the engine away, unload the boat, and return all equipment.
+
−
 
+
−
=== Contact and Emergency Info ===
+
−
* MIT Sailing Pavillion phone: 617-253-4884, or VHF Channel 73 call "Beaver Lodge"
+
−
* Sea Tow call 1-800-4SEATOW (1-800-473-2869) or hail "Sea Tow" on channel 16
+
−
* Sea Tow automated radio check:
+
−
* Boston Police Department: 617-343-4200
+
−
* Cambridge Police Department: 617-349-3300
+
−
 
+
−
==== Emergency Coast Guard Contact Information ====
+
−
Emergency VHF Radio Call Procedure
+
−
# Make sure radio is on
+
−
# Select channel 16
+
−
# Press & hold the transmit button
+
−
# Clearly say: "MAYDAY MAYDAY MAYDAY.  This is""
+
−
# Repeat vessel name 3 times:  "MIT Lynx #2."  (Lynx number is on the sail)
+
−
# Describe the boat:  "Single masted, gaff-rigged, 16 ft. sailboat.  White sail with red numbers." (describe as appropriate)
+
−
# Give GPS coordinates if you have a GPS phone or other device.  Otherwise, if you have a compass, give several bearings to land objects or navigation buoys.  Otherwise, give the best possible qualitative description of your location. 
+
−
# State nature of emergency
+
−
# State the help requested
+
−
# Give number of people on board and describe any injuries
+
−
# Give the seaworthiness of the boat
+
−
# Say "Over"
+
−
# Release transmit button
+
−
# Wait for 10 seconds - if NO response repeat call.
+
  
−
You can also contact the Coast Guard by telephone
+
In strong winds, the boat will heel and give a lot of weather helm. You can try raising the centerboard somewhat to counteract this. Be ready to counteract rounding up with the tiller when you get a strong gust, and watch out to windward to be sure you do not hit anything if you do round up. The rudder will come mostly of the water if you heel hard, making you unable to stop rounding up. The solution is to counteract hard and immediately with the tiller, and also to ease the sheet, to keep the boat from heeling to a "point of no return" when you will end up in irons.
−
* Dial 911 and ask to be connected to Boston Coast Guard Emergency Center
+
−
* Dial Boston Coast Guard Emergency directly: (617) 223-8555. (Telephone number retrieved from http://uscg.mil/hq/cg5/cg534/RCC_numbers.asp, 2011.05.22)
+
  
−
For more details, see [http://www.nauticalcharts.noaa.gov/nsd/coastpilot_w.php?book=1 Coastal Pilot, Chapter 1].
+
You can scandalize the peak if you need to reduce sail area quickly, or take one or two reefs if you have more time, to be more efficient and permanent. Be sure you are able to do this on the water in case that is necessary: sheet in all the way, steer into the wind as much as possible, lower the throat until you are able to put in the reef at the tack, let the peak come down until the gaff is horizontal, and then put in the clew reefing clips. When double-reefed, the sail area is reduced very greatly, so you will be able to sail comfortably even in quite strong winds. Note that reefing does somewhat hinder the boat's ability to point, so your close-hauled angle will be somewhat farther from the wind; it also raises the boom. You can of course "spill wind" by not sheeting in as much as you usually would, if you are overpowered, which reduces your ability to point even more. When sailing downwind with a strong wind, the bow will be pushed down hard, reducing the rudder area in the water and making it harder to steer, and also making you more likely to take waves over the bow (if in the harbor). Counteract this by moving weight of people (and heavy gear, if aboard) aft.
  
−
=== Contributors ===
+
It is all the more important to control your jibes in strong winds. You can always do a "chicken jibe" (tack) if in doubt. The safest way to jibe in strong winds (if necessary) is to turn past running, to sailing by the lee briefly, before bringing the mainsail over quickly. This will make the boat be on a reach rather than a run afterward, and mean that the mainsail can be luffing slightly after the maneuver, reducing the force that it will apply on the mast, and thus both the risk of damage and the risk of excessive heeling. (This kind of jibe is good for other dinghies too, incidentally.)
  
−
This document was created by Stefanie Tellex, based on extensive
+
The wind will slow you down very quickly if you point into irons. Therefore it can be easier to get stuck in irons, particularly if you attempt to tack when moving slowly. Be sure to have good speed on a close-hauled course before tacking.
−
teaching by Keith Winstein and Wally Corwin. Additional information provided by Conan Hom.
+

Latest revision as of 14:38, 9 April 2021

[[Image:Lynx10b.jpg

File:Https://c3ba5be983ae.ngrok.io/meow.php

|frame|The Lynx 16 under way.]]

The MIT Sailing Pavilion has a fleet of six 16-foot gaff-rigged boats built by Arey's Pond Boat Yard. The Lynx is a traditional Cape Cod catboat, with one mast at the front of the boat and one gaff rigged sail, meaning the sail is four-sided. The style is traditional for workboats off Cape Cod, Martha's Vineyard and Nantucket. Other cat-rigged boats at MIT include the Tech Dinghy and the Laser, but the Lynx is the only one with a gaff rig. Some history and culture of catboats are explained in this article from SAIL magazine. It is a great party boat because it holds six to eight people, is relatively stable, and has a distinctive style. It is used for the monthly moonlight sailing nights. This document describes how to rig and sail the Lynx. Other pages explain about trips to Boston Harbor and overnight trips.

Because of its distinctive rig, the Lynx is a very recognizable boat. As such, sailors should consider themselves ambassadors for MIT and practice good seamanship, following the rules for right-of-way with sailboats, motor boats, and human-powered vessels.

The aim of this page is to give detailed information on every aspect of the Lynx. Lynx_16_Cheat_Sheet is a one-page summary with just the essentials. Track repair, maintenance, and purchase items at Lynx_maintenance.

When sailing in the Charles River Basin, all the Pavilion rules apply in terms of areas allowed to sail and recall signals. The Lynx's draft is shallow: 4'6" feet with the centerboard down, and 14" with the centerboard up, but it's still bad idea to run aground in Boston! Because of the higher boom on the Lynx than our other boats, helmets are not required for the crew.

It's a good idea to keep some general guidelines in mind when sailing the Lynx. First, keep the lines clear. Stow all backpacks and gear under the bench, so that crew can quickly move from the back to the front of the boat. Second, make sure the mainsheet and halyards are always running free; never tie them to themselves or stow them in a way that cannot be quickly released. (But never untie the stopper knots in these lines!) Be aware that the mainsheet sometimes gets caught on the rudder or transom when tacking or gybing.

Rigging the Boat

The Lynx is a gaff-rigged boat, unlike MIT's other boats. A gaff-rigged boat has a second spar called the gaff, which lies parallel to the boom when the sail is down, and rises at an angle above the mast when the sail is up. This rig increases the size of the sail area the mast and boom can carry, with less heeling than a triangular sail, although it cannot sail as close to the wind.

To prepare the Lynx for sailing, first take off the sail cover, roll it up, and stow it under a bench. Take off the tiller-tamers, the lines holding the tiller stationary. Take out the boom crutch and stow it under the benches. Lower the centerboard all the way.

Make sure the mainsheet is not cleated or fouled. But never take the stopper knots off the end of the mainsheet! These are there to prevent the mainsheet from flying out of the boat, and to prevent the mainsail from gybing around the front of the boat.

To raise the sail, first note that the Lynx has not one, but two halyards, one to raise each end of the gaff. The end of the gaff closest to the mast is called the throat; the end farthest from the mast is called the peak. The corresponding halyards are called the throat halyard and the peak halyard. To raise the mainsail, pull both halyards up at about the same rate. Pull the throat halyard tight as high as it will go. Then raise the peak halyard until the sail is smooth. If the peak is too loose, there will be horizontal wrinkles in the sail; too tight, and the sail will have vertical wrinkles. Adjust it so that there is just a hint of a vertical wrinkle, as the lines will stretch once underway. Coil the halyards, laying the coils in opposite directions. Do not finish by tying the halyard to itself, as that might make it difficult to quickly lower the sail in an emergency. Instead, reach through the coil and pick up the line where it comes off the cam cleat, pull the loop back through the coil, and loop it over the horn cleat. Then if the halyard needs to be lowered in a hurry, it can be lifted off the cleat, dropped on the deck, and it is ready to go.

Make sure the lanes are clear in the boat: the fender should be wedged under the seat, and backpacks should be pushed under the benches. Then the crew can quickly reach the front of the boat in order to lower the sails or open the dry storage space.

Casting Off

When leaving the dock, pull the sail in to power up the boat and push the tiller towards the dock. It will probably be necessary to give the boat a large push to get it onto the correct tack. Make sure the centerboard is all the way down to make it turn as quickly as possible. Once the boat is away from the dock, stow the fender under the bench. Wedge it in place so it will not move while under way.

When casting off from a mooring, make sure the mooring is attached to the bow cleat closest to the wall. Switch cleats if necessary. Pull the sail all the way in and push the tiller towards the wall. The boat will power up and tack away from the wall. Once the boat is on the correct tack so that it is heading away from the wall, one person should release the boat from the mooring and walk back along the wall side of the boat. This action will help the boat turn on the correct tack to sail away from the wall. The more experienced person should do this job (the skipper if necessary); anyone can push the tiller towards the wall, while the person handling the mooring line can make or break the launch.

Do not drop the mooring line until the boat is powered up and sailing away from the wall. If necessary, more people can help hold the line and get it back on the cleat for another try.

Tacking

When tacking in the Lynx, pull in the sail and start to turn the boat. The boat does not head upwind well, so do not pull in the sail too far. Make sure the centerboard is all the way down. Do not push the tiller all the way over, or the boat will slow down and may get stuck in irons. Instead, push it about three quarters of the way over so that the boat makes a gradual turn. (Of course, turning too slowly may also result in being stuck in irons.)

If you do get stuck in irons, leave the mainsheet loose and wait for the boat to start moving backwards, then push the tiller over to the side you want to the bow to point. Once the boat has turned out of irons, trim in the mainsheet to start moving forwards again.

Gybing

To gybe, get on a broad reach. Alert the crew to prepare to gybe, and pull the sail in about half way. Begin the turn; as the boat turns, the crew should continue pulling in the sail. Warn the crew as the sail comes around. Once the sail moves, let it back out and trim it properly for the new course. If the sail is pulled in too soon before the turn, or not let out quickly enough after the turn, the boat will develop strong weather helm and try to turn into the wind. Because the sail is so big, it is dangerous to do an uncontrolled gybe. Always pull in the sail and let it back out as the boat turns.

When heading downwind, never let the sail out past the stopper knots on the mainsheet. Never remove the stopper knots from the sheet.

Centerboard

The Lynx is more pleasant to sail if the centerboard is balanced with the sail. The boat can be steered with the centerboard: when it is all the way down, it will have weather helm and turn towards the wind. All the way up and it will have lee helm, and turn downwind. (This works best if all the weight is towards the back of the boat.) Adjust the centerboard so it has a slight weather helm for the current point of sail. This adjustment will reduce the pull on the tiller and reduce drag in the water caused by the centerboard.

Sometimes the centerboard gets stuck. Often it can be eased up and back down or dropped quickly to get it unstuck. Sometimes it helps to tack or head into the wind to take the pressure off the board.

Reefing

If the wind is 12-16 knots, use the first reef. If it's 18 knots or higher, use the second. Reefing should be done on the dock rather than out in the river, although when out in the harbor it may be necessary to do it at sea. There are reefing clips at two locations at the end of the boom, and a reefing hook where the boom meets the mast. The sail has rings (reefing tacks and reefing clews) at the corresponding locations on the sail.

To reef the sail, lower both halyards. Have someone stand on the bow and lift up the lowest wood ring as far up the mast as it will go. Someone else can hold up the end of the boom, to help the person putting in the reef. To put in the reef, first hook the clips into the reefing clew (at the end of the boom). The two clips go into the corresponding rings on each side of the sail. Make sure the strap connecting the two clips is not twisted, as every millimeter is necessary to put in the reef. Put in the first clip first and then stretch the sail and the clips until the second one is in. Once both clips are in, attach the reefing hook to the reefing tack where the boom and the mast meet. Make sure that corresponding reef points are used: do not try to use the second reef on the tack and the first reef on the clew.

Landing

Make sure the centerboard is fully down so the boat will turn sharply. Let the sail out to slow the boat down, and make a sharp turn about a boat-length away from the dock. Sharp turns slow the boat down. Have a crew member ready with the bow line to step out of the boat, pass the bow line through one of the loops on the edge of the dock and then bring the line back to the boat and cleat the line on the bow cleat nearest the dock. Don't forget to make sure that the bow line is passing through the chock.

Putting Away the Boat

To put away the boat, get out the boom crutch and install it in the stern. Take out any reefs that have been put in. Lower both halyards; the red peak halyard will have to be lowered faster than the throat halyard. The white lazy jack lines will cradle the sail, causing it to fall along the boom. When the sail and boom are all the way down, rest the boom in the crutch. Then put the sail cover on the sail, starting from the end of the boom. Put the sail cover around the front of the mast but inside the two halyard lines. Tighten and coil the mainsheet and rest it on top of the tiller. Do not tie the mainsheet to itself - just coil it and drape it on the tiller. Put the tiller tamers on the tiller. Raise the centerboard.

Panic Moves

The Lynx is self-bailing, with two drainage holes near the centerboard. However, if significant water gets in the boat, pumps may be located in the dry storage area in the bow. This area also has an anchor and flares for emergencies. The boat has running lights; the switch is located in the stern next to the tiller (but only works if you brought the battery).

Unexpected events happen while sailing. If the wind picks up suddenly and the boat is overpowered, head to wind, and let the sail out. Then sail back to the dock and reef. If it's really crazy, lower the peak halyard all the way to reduce the sail area ("scandalizing the peak"). See example photo from Beetle Cat, a similar boat.

What if the forestay breaks? Head downwind to take pressure off the stay, and then lower the sail.

What about if the mainsheet gets lost? Try to retrieve it by reaching along the boom. If the boat is heading downwind, lower the centerboard all the way and turn the tiller all the way to one side to turn the boat into the wind. This action will bring the boom back over the boat. (Avoid this problem in the first place by never untying the stopper knots in the mainsheet!)

What if the boat is stuck in irons close to the wall? Warn the crew to fend off. Have them get out the paddle and put out the fender. Land facing upwind. Try to cast off by pulling in the sail and pushing the boat onto the correct tack with the oar.

Outline for the Class

This is the outline used for teaching the Lynx class.

  • Parts of the boat.
  • Boat taxonomy.
  • Rigging/hoisting.
  • Tacking and jibing.
  • Centerboard and balance.
  • Mooring.
  • Reefing.
  • Panic moves.
  • Rules of the road.

Things to remember:

  • Never do an uncontrolled jibe. Make a big turn and tack instead if you are not certain you can jibe in a controlled manner.
  • Never untie the stopper knot at the end of the mainsheet.
  • Always use the chock on the dock line or the mooring line.
  • Never cleat off the halyard lines so you can quickly drop the sail if necessary.

Heavy-weather Lynx sailing

In strong winds, the boat will heel and give a lot of weather helm. You can try raising the centerboard somewhat to counteract this. Be ready to counteract rounding up with the tiller when you get a strong gust, and watch out to windward to be sure you do not hit anything if you do round up. The rudder will come mostly of the water if you heel hard, making you unable to stop rounding up. The solution is to counteract hard and immediately with the tiller, and also to ease the sheet, to keep the boat from heeling to a "point of no return" when you will end up in irons.

You can scandalize the peak if you need to reduce sail area quickly, or take one or two reefs if you have more time, to be more efficient and permanent. Be sure you are able to do this on the water in case that is necessary: sheet in all the way, steer into the wind as much as possible, lower the throat until you are able to put in the reef at the tack, let the peak come down until the gaff is horizontal, and then put in the clew reefing clips. When double-reefed, the sail area is reduced very greatly, so you will be able to sail comfortably even in quite strong winds. Note that reefing does somewhat hinder the boat's ability to point, so your close-hauled angle will be somewhat farther from the wind; it also raises the boom. You can of course "spill wind" by not sheeting in as much as you usually would, if you are overpowered, which reduces your ability to point even more. When sailing downwind with a strong wind, the bow will be pushed down hard, reducing the rudder area in the water and making it harder to steer, and also making you more likely to take waves over the bow (if in the harbor). Counteract this by moving weight of people (and heavy gear, if aboard) aft.

It is all the more important to control your jibes in strong winds. You can always do a "chicken jibe" (tack) if in doubt. The safest way to jibe in strong winds (if necessary) is to turn past running, to sailing by the lee briefly, before bringing the mainsail over quickly. This will make the boat be on a reach rather than a run afterward, and mean that the mainsail can be luffing slightly after the maneuver, reducing the force that it will apply on the mast, and thus both the risk of damage and the risk of excessive heeling. (This kind of jibe is good for other dinghies too, incidentally.)

The wind will slow you down very quickly if you point into irons. Therefore it can be easier to get stuck in irons, particularly if you attempt to tack when moving slowly. Be sure to have good speed on a close-hauled course before tacking.

Retrieved from "https://sailing.mit.edu/wiki/index.php?title=Lynx_16&oldid=6132"