Engine schematic dgm

From MITNA
Jump to: navigation, search
(return UP to Systems Descripts or ACROSS to Engine Wiring Diagram)

.)

(See NOTES related to Nevermore's configuration of engine circuits located after the right-hand part of the diagram later below.)

Engine electrical schematic diagram from Tartan manual

This schematic diagram appears on page Q.2 of the Engine Tech Manual. Page Q.2 has some prose across the top, and the diagrams below, in two columns. Herebelow, we have split the left and right columns of the one original diagram into two diagrams. Note that the correct "schematic insert" on the two halves of page Q.2 must be used, as is discussed more in OUR first note following the second figure below.

Also see the wiring diagram showing the same electrical functionality but also delineating how the engine and control panel are actually wired.

Engine

(Above) Left-hand side of page Q.2 of schematic in Tartan Tech Manual

(See NOTES related to Nevermore's configuration of engine circuits located after the the diagram below.)

W50schemQ2-P1090672-bc96p-right.JPG

(Above) Right-hand side of page Q.2 of schematic in Tartan Tech Manual


NOTES related to Nevermore's engine wiring configuration:

  • See page Q.2 right-hand side for the SCHEMATIC INSERT for Westerbeke 50 engine's starter and glow-plugs. This diagram replaces the INSERT on the left-side schematic. Nevermore has 4 glow-plugs, not a pre-heater, and has a starter with integral solenoid; the starter's "minus" is grounded within the starter, which is bolted to the engine.
  • The 2 user-provided CktBrkrs (parts 45 & 46, discussed in written notes circle-B and circle-C), are mounted on a vertically oriented metal bracket located about an inch aft of of the dip-stick pipe, and a few inches below the dipstick handle. They can be seen from the companionway area (see Engine_40_10_CBs_panel_access pictures.)

The vertically oriented panel and buttons (plus a couple of mounting screws) are visible, and the "10" and "40" amperage ratings are vaguely visible.

  • Note circle-A on the schematic relates to the need for two battery switching functions, named "SW1-1" and "SW1-2":
    • Switch SW1-1 12-V battery switch is an "on-off switch .... to disconnect the starter circuit from the battery in an emergency or when leaving the boat ...". This function is provided by Nevermore's upper rotary main battery switch under the nav station seat (the lower main switch isn't used (2009)).
    • Switch SW1-2 (under the "regulator" block on the diagram) is not wired on Nevermore. Without it, THE ALTERNATOR WILL BE DAMAGED if we switch off SW1-1, i.e. the top main battery switch.
      • We assume that Nevermore's SW1-2 is always made "ON" by the hard-wiring between the regulator and the "field" connection on the alternator. If this wire were replaced by the AFD contacts in the main battery switch, we could alleviate this failure of the alternator.
      • Another way to give the alternator protection function of SW1-2 is with a shunt (diode) which limits the alternator voltage when it has no load, i.e. when the 2 battery switches are OFF.
      • The way we get the altelrnator protection functionality that SW1-2 would give is with our rococco battery-switching SOPs.
  • We think the optional SPLITTER (part 44) is not installed. We believe that Nevermore's schematic can be read with a metal connection between terminals "A" and "1" on the splitter on the schematic, with terminal "2" unwired.
    • Tech Manual page V.11 Service Bulletin #87 discusses adding the optional splitter. To account for voltage drop across the splitter, it says to "connect regulator wire directly to alternator output rather than to the regulator terminals". (Thom can't make sense of this on the schematic without the Svc Bull 22Sep07).
    • TODO: Per above note, (1) see if Svc Bull. #87 shows the "...regulator wire..." connection, and (2) see if we need to make a NOTE that changes the wiring at the alternator in the schematic above to agree with NOT having the splitter installed.
  • FUEL PRESSURE SWITCH, item 11 on schematic:
    • The prose at top of page Q.2 diagram discusses the operation of this switch, how it functions in lieu of an "ignition switch" for starting the engine. Turning on the nav station main battery switch allows cranking of the engine from the cockpit control panel. This cranking operates the fuel pump, causing fuel pressure to build up, closing the switch, thus activating engine instrument readings; water over-temp and oil under-pressure alarms, and alternator output for battery charging.
    • This switch is shown in the Nevermore Tech Manual page V.15, Service Bulletin #94. This alignment of the switch -- normal to a plane thru the long axis of the pump -- is more like Nevermore's configuration than the parts list figure (page 214 & 216 item #33) that shows it parallel to the pump's long axis.
    • This switch is shown in the Parts List pages 214 & 216 (identical) as item #33, attached to the Injection Pump item #41 via adaptor #32 and other little hardware; it's also shown on page 218 as item #6, seemingly the same parts as in the page 214 picture; this drawing is the same as in Svc. Bull. #94.
    • Comment circle-G on right hand side of diagram is moot for Nevermore; we don't seem to require additional fuel-pressure switches to turn on other electrical equipment.
  • The schematic's note circle-I isn't operative, since the control panel IS installed.